View source for Engineering:British Standard Pipe

{{Short description|Standard set of screw thread sizes used in pipe fittings}}
{{Use Oxford spelling|date=December 2011}}
'''British Standard Pipe''' ('''BSP''') is a set of [[Technical standard|technical standard]]s for [[Engineering:Screw thread|screw thread]]s that has been adopted internationally for interconnecting and sealing [[Chemistry:Piping|pipes and fittings]] by mating an external ([[Engineering:Gender of connectors and fasteners|male]]) thread with an internal (female) thread. It has been adopted as standard in [[Engineering:Plumbing|plumbing]] and [[Engineering:Pipefitter|pipe fitting]], except in North America, where [[Engineering:National pipe thread|NPT and related threads]] are used.

==Types==
[[File:BSPP Male Straight Thread.png|thumb|BSPP fitting]]
Two types of threads are distinguished:
* Parallel (straight) threads, ''British Standard Pipe Parallel thread'' (''BSPP''; originally also known as<ref>{{cite web|url=http://www.ring-plug-thread-gages.com/ti-bspm-British-Standard-Pipe-Mechanical.htm|title=BSPM = British Standard Pipe Mechanical|access-date=14 July 2016}}</ref> ''British Standard Pipe Fitting thread''/''BSPF'' and ''British Standard Pipe Mechanical thread''/''BSPM''), which have a constant diameter; denoted by the letter ''G''.
* Taper threads, ''British Standard Pipe Taper thread'' (''BSPT''), whose diameter increases or decreases along the length of the thread; denoted by the letter ''R''.

[[File:Colder BSPT Threads.png|thumb|BSPT Pipe Threads.<ref>{{cite web |url=http://www.colder.com/Portals/0/Library/Resources/Literature/WhitePapers/Documents/NPT_whitepaper.pdf |title=Pipe Thread Types and Designations |access-date=2013-12-27 |url-status=dead |archive-url=https://web.archive.org/web/20131007174133/http://www.colder.com/Portals/0/Library/Resources/Literature/WhitePapers/Documents/NPT_whitepaper.pdf |archive-date=2013-10-07 }}</ref>]]
These can be combined into two types of joints:
; Jointing threads: These are pipe threads where pressure-tightness is made through the mating of two threads together. They always use a taper male thread, but can have either parallel or taper female threads. (In Europe, taper female pipe threads are not commonly used.)
; Longscrew threads: These are parallel pipe threads used where a pressure-tight joint is achieved by the compression of a soft material (such as an o-ring seal or a washer) between the end face of the male thread and a socket or nipple face, with the tightening of a backnut.

==Thread form==
The thread form follows the [[Engineering:British Standard Whitworth|British Standard Whitworth]] standard:

* Symmetrical V-thread in which the angle between the flanks is 55° (measured in an axial plane)
* One-sixth of this sharp V is truncated at the top and the bottom
* The threads are rounded equally at crests and roots by circular arcs ending tangentially with the flanks where r ≈ 0.1373''P''
* The theoretical depth of the thread is therefore 0.6403 times the nominal pitch h ≈ 0.6403''P''

==Pipe thread sizes==

At least 41 thread sizes have been defined, ranging from <sup>1</sup>⁄<sub>16</sub> to 18, although of these only 15 are included in ISO 7 and 24 in ISO 228.<ref>{{cite web|url=http://mdmetric.com/tech/thddat7.htm|title=Maryland Metrics thread data charts|author=maryland metrics|access-date=14 July 2016|url-status=dead|archive-date=24 July 2018|archive-url=https://web.archive.org/web/20180724110116/http://mdmetric.com/tech/thddat7.htm}}</ref><ref>{{cite web|url=http://www.roymech.co.uk/Useful_Tables/Flanges/Pipe_Threads.html|title=RoyMech: Pipe Threads|access-date=14 July 2016|archive-date=22 July 2018|archive-url=https://web.archive.org/web/20180722082552/http://www.roymech.co.uk/Useful_Tables/Flanges/Pipe_Threads.html|url-status=dead}}</ref><ref>{{cite web|url=http://www.pipefittingsdirect.co.uk/contents/en-uk/BSP%20Identification1.pdf|title=How to ID British (BSP) Threads|access-date= 20 November 2017}}</ref><ref>{{Cite web|url=http://www.practicalmachinist.com/vb/general/bsp-thread-data-245989/|title=BSP Thread data|website=www.practicalmachinist.com|date=2 May 2012 |access-date=2016-07-15}}</ref>  The size number was originally based on the ''inner'' diameter (measured in inches) of a steel tube for which the thread was intended, but contemporary pipes tend to use thinner walls to save material, and thus have an inner diameter larger than this nominal size.  In the modern standard metric version, it is simply a size number, where listed diameter size is the major outer diameter of the external thread. For a taper thread, it is the diameter at the "gauge length" (plus/minus one thread pitch) from the small end of the thread. The taper is 1:16, meaning that for each 16 units of measurement increase in the distance from the end, the diameter increases by 1 unit of measurement.

{| class=wikitable
|-
! rowspan=2            | G{{thinsp}}/{{thinsp}}R<br>size
! rowspan=2            | Thread<br/>density<br>(TPI)
! rowspan=2            | Thread<br/>pitch
! rowspan=2  colspan=2 | Major<br/>diameter
! rowspan=2  colspan=2 | Minor<br/>diameter
! rowspan=2  colspan=2 | Gauge<br/>length
!            colspan=2 | Tapping drill
|-
! scope="col" | {{small|R 95%}} !! scope="col" | {{small|G 80%}}
|-
! scope="col" | {{small|(in)}}
! scope="col" | {{small|(in{{sup|−1}})}} !! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(in)}} !! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(in)}} !! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(in)}} !! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(mm)}}
|- align="right"
| align="center" | {{frac|1|16}}
| 28 || {{convert|1/28|in|mm|3|disp=number}}
| {{convert|7.723|mm|in|disp=table|order=flip}}
| {{convert|6.561|mm|in|disp=table|order=flip}}
| {{convert|5/32|in|mm|1|disp=table}}
| 6.6 || 6.8
|- align="right"
| align="center" | {{frac|1|8}}
| 28 || {{convert|1/28|in|mm|3|disp=number}}
| {{convert|9.728|mm|in|disp=table|order=flip}}
| {{convert|8.566|mm|in|disp=table|order=flip}}
| {{convert|5/32|in|mm|1|disp=table}}
| 8.6 || 8.8
|- align="right"
| align="center" | {{frac|1|4}}
| 19 || {{convert|1/19|in|mm|3|disp=number}}
| {{convert|13.157|mm|in|disp=table|order=flip}}
| {{convert|11.445|mm|in|disp=table|order=flip}}
| {{font|size=75%|0.2367}} || {{convert|0.2367|in|mm|1|disp=number}}
| 11.5 || 11.8
|- align="right"
| align="center" | {{frac|3|8}}
| 19 || {{convert|1/19|in|mm|3|disp=number}}
| {{convert|16.662|mm|in|disp=table|order=flip}}
| {{convert|14.950|mm|in|disp=table|order=flip}}
| {{convert|1/4|in|mm|1|disp=table}}
| 15.0 || 15.3
|- align="right"
| align="center" | {{frac|1|2}}
| 14 || {{convert|1/14|in|mm|3|disp=number}}
| {{convert|20.955|mm|in|disp=table|order=flip}}
| {{convert|18.631|mm|in|disp=table|order=flip}}
| {{font|size=75%|0.3214}} || {{convert|0.3214|in|mm|1|disp=number}}
| 18.7 || 19.1
|- align="right"
| align="center" | {{frac|5|8}}
| 14 || {{convert|1/14|in|mm|3|disp=number}}
| {{convert|22.911|mm|in|disp=table|order=flip}}
| {{convert|20.587|mm|in|disp=table|order=flip}}
| {{font|size=75%|0.3214}} || {{convert|0.3214|in|mm|1|disp=number}}
| 20.7 || 21.1
|- align="right"
| align="center" | {{frac|3|4}}
| 14 || {{convert|1/14|in|mm|3|disp=number}}
| {{convert|26.441|mm|in|disp=table|order=flip}}
| {{convert|24.117|mm|in|disp=table|order=flip}}
| {{convert|3/8|in|mm|1|disp=table}}
| 24.2 || 24.6
|- align="right"
| align="center" | {{frac|7|8}}
| 14 || {{convert|1/14|in|mm|3|disp=number}}
| {{convert|30.201|mm|in|disp=table|order=flip}}
| {{convert|27.877|mm|in|disp=table|order=flip}}
| {{convert|3/8|in|mm|1|disp=table}}
| 28.0 || 28.3
|- align="right"
| align="center" | 1
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert| 33.249 |mm|in|disp=table|order=flip}}
| {{convert| 30.291 |mm|in|disp=table|order=flip}}
| {{font|size=75%|0.4091}} || {{convert|0.4091|in|mm|1|disp=number}}
| 30.4 || 30.9
|- align="right"
| align="center" | {{frac|1|1|8}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|37.897|mm|in|disp=table|order=flip}}
| {{convert|34.939|mm|in|disp=table|order=flip}}
| {{font|size=75%|0.4091}} || {{convert|0.4091|in|mm|1|disp=number}}
| 35.1 || 35.5
|- align="right"
| align="center" | {{frac|1|1|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|41.910|mm|in|disp=table|order=flip}}
| {{convert|38.952|mm|in|disp=table|order=flip}}
| {{convert|1/2|in|mm|1|disp=table}}
| 39.1 || 39.5
|- align="right"
| align="center" | {{frac|1|3|8}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|44.323|mm|in|disp=table|order=flip}}
| {{convert|41.365|mm|in|disp=table|order=flip}}
| {{convert|1/2|in|mm|1|disp=table}}
| 41.5 || 42.0
|- align="right"
| align="center" | {{frac|1|1|2}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|47.803|mm|in|disp=table|order=flip}}
| {{convert|44.845|mm|in|disp=table|order=flip}}
| {{convert|1/2|in|mm|1|disp=table}}
| 45.0 || 45.4
|- align="right"
| align="center" | {{frac|1|5|8}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|52.883|mm|in|disp=table|order=flip}}
| {{convert|49.926|mm|in|disp=table|order=flip}}
| {{convert|5/8|in|mm|1|disp=table}}
| 50.1 || 50.5
|- align="right"
| align="center" | {{frac|1|3|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|53.746|mm|in|disp=table|order=flip}}
| {{convert|50.788|mm|in|disp=table|order=flip}}
| {{convert|5/8|in|mm|1|disp=table}}
| 50.9 || 51.4
|- align="right"
| align="center" | {{frac|1|7|8}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|56.998|mm|in|disp=table|order=flip}}
| {{convert|54.041|mm|in|disp=table|order=flip}}
| {{convert|5/8|in|mm|1|disp=table}}
| 54.2 || 54.6
|- align="right"
| align="center" | 2
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|59.614|mm|in|disp=table|order=flip}}
| {{convert|56.656|mm|in|disp=table|order=flip}}
| {{convert|5/8|in|mm|1|disp=table}}
| 56.8 || 57.2
|- align="right"
| align="center" | {{frac|2|1|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|65.710|mm|in|disp=table|order=flip}}
| {{convert|62.752|mm|in|disp=table|order=flip}}
| {{convert|11/16|in|mm|1|disp=table}}
| 62.9 || 63.3
|- align="right"
| align="center" | {{frac|2|1|2}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|75.184|mm|in|disp=table|order=flip}}
| {{convert|72.226|mm|in|disp=table|order=flip}}
| {{convert|11/16|in|mm|1|disp=table}}
| 72.4 || 72.8
|- align="right"
| align="center" | {{frac|2|3|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|81.534|mm|in|disp=table|order=flip}}
| {{convert|78.576|mm|in|disp=table|order=flip}}
| {{convert|13/16|in|mm|1|disp=table}}
| 78.7 || 79.2
|- align="right"
| align="center" | 3
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|87.884|mm|in|disp=table|order=flip}}
| {{convert|84.926|mm|in|disp=table|order=flip}}
| {{convert|13/16|in|mm|1|disp=table}}
| 85.1 || 85.5
|- align="right"
| align="center" | {{frac|3|1|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|93.980|mm|in|disp=table|order=flip}}
| {{convert|91.022|mm|in|disp=table|order=flip}}
| {{convert|7/8|in|mm|1|disp=table}}
| 91.2 || 91.6
|- align="right"
| align="center" | {{frac|3|1|2}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|100.330|mm|in|disp=table|order=flip}}
| {{convert|97.372|mm|in|disp=table|order=flip}}
| {{convert|7/8|in|mm|1|disp=table}}
| 97.5 || 98.0
|- align="right"
| align="center" | {{frac|3|3|4}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|106.680|mm|in|disp=table|order=flip}}
| {{convert|103.722|mm|in|disp=table|order=flip}}
| {{convert|7/8|in|mm|1|disp=table}}
| 103.9 || 104.3
|- align="right"
| align="center" | 4
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|113.030|mm|in|disp=table|order=flip}}
| {{convert|110.072|mm|in|disp=table|order=flip}}
| {{convert|1|in|mm|1|disp=table}}
| 110.2 || 110.7
|- align="right"
| align="center" | {{frac|4|1|2}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|125.730|mm|in|disp=table|order=flip}}
| {{convert|122.772|mm|in|disp=table|order=flip}}
| {{convert|1|in|mm|1|disp=table}}
| 122.9 || 123.4
|- align="right"
| align="center" | 5
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|138.430|mm|in|disp=table|order=flip}}
| {{convert|135.472|mm|in|disp=table|order=flip}}
| {{convert|1+1/8|in|mm|1|disp=table}}
| 135.6 || 136.1
|- align="right"
| align="center" | {{frac|5|1|2}}
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|151.130|mm|in|disp=table|order=flip}}
| {{convert|148.172|mm|in|disp=table|order=flip}}
| {{convert|1+1/8|in|mm|1|disp=table}}
| 148.3 || 148.8
|- align="right"
| align="center" | 6
| 11 || {{convert|1⁄11|in|mm|3|disp=number}}
| {{convert|163.830|mm|in|disp=table|order=flip}}
| {{convert|160.872|mm|in|disp=table|order=flip}}
| {{convert|1+1/8|in|mm|1|disp=table}}
| 161.0 || 161.5
|- align="right"
| align="center" | 7
| 10 || {{convert|1⁄10|in|mm|3|disp=number}}
| {{convert|7.4500|in|mm|3|disp=table}}
| {{convert|7.3220|in|mm|3|disp=table}}
| {{convert|1+3/8|in|mm|1|disp=table}}
| 186.1 || 186.6
|- align="right"
| align="center" | 8
| 10 || {{convert|1⁄10|in|mm|3|disp=number}}
| {{convert|8.4500|in|mm|3|disp=table}}
| {{convert|8.3220|in|mm|3|disp=table}}
| {{convert|1+1/2|in|mm|1|disp=table}}
| 211.5 || 212.0
|- align="right"
| align="center" | 9
| 10 || {{convert|1⁄10|in|mm|3|disp=number}}
| {{convert|9.4500|in|mm|3|disp=table}}
| {{convert|9.3220|in|mm|3|disp=table}}
| {{convert|1+1/2|in|mm|1|disp=table}}
| 236.9 || 237.4
|- align="right"
| align="center" | 10
| 10 || {{convert|1⁄10|in|mm|3|disp=number}}
| {{convert|10.4500|in|mm|3|disp=table}}
| {{convert|10.3220|in|mm|3|disp=table}}
| {{convert|1+5/8|in|mm|1|disp=table}}
| 262.3 || 262.8
|- align="right"
| align="center" | 11
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|11.4500|in|mm|3|disp=table}}
| {{convert|11.2900|in|mm|3|disp=table}}
| {{convert|1+5/8|in|mm|1|disp=table}}
| 287.0 || 287.6
|- align="right"
| align="center" | 12
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|12.4500|in|mm|3|disp=table}}
| {{convert|12.2900|in|mm|3|disp=table}}
| {{convert|1+5/8|in|mm|1|disp=table}}
| 312.4 || 313.0
|- align="right"
| align="center" | 13
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|13.6800|in|mm|3|disp=table}}
| {{convert|13.5200|in|mm|3|disp=table}}
| {{convert|1+5/8|in|mm|1|disp=table}}
| 343.6 || 344.2
|- align="right"
| align="center" | 14
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|14.6800|in|mm|3|disp=table}}
| {{convert|14.5200|in|mm|3|disp=table}}
| {{convert|1+3/4|in|mm|1|disp=table}}
| 369.0 || 369.6
|- align="right"
| align="center" | 15
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|15.6800|in|mm|3|disp=table}}
| {{convert|15.5200|in|mm|3|disp=table}}
| {{convert|1+3/4|in|mm|1|disp=table}}
| 394.4 || 395.0
|- align="right"
| align="center" | 16
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|16.6800|in|mm|3|disp=table}}
| {{convert|16.5200|in|mm|3|disp=table}}
| {{convert|1+7/8|in|mm|1|disp=table}}
| 419.8 || 420.4
|- align="right"
| align="center" | 17
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|17.6800|in|mm|3|disp=table}}
| {{convert|17.5200|in|mm|3|disp=table}}
| {{convert|2|in|mm|1|disp=table}}
| 445.2 || 445.8
|- align="right"
| align="center" | 18
| 8 || {{convert|1⁄8|in|mm|3|disp=number}}
| {{convert|18.6800|in|mm|3|disp=table}}
| {{convert|18.5200|in|mm|3|disp=table}}
| {{convert|2|in|mm|1|disp=table}}
| 470.6 || 471.2
|}

These standard pipe threads are formally referred to by the following sequence of blocks:
* the words, ''Pipe thread'',
* the document number of the standard (e.g., ''ISO 7'' or ''EN 10226'')
* the symbol for the pipe thread type:
** ''G'', external and internal parallel (ISO 228)
** ''R'', external taper (ISO 7)
** ''Rp'', internal parallel (ISO 7/1)
** ''Rc'', internal taper (ISO 7)
** ''Rs'', external parallel
* the thread size

Threads are normally right-hand. For left-hand threads, the letters, ''LH'', are appended.

Example: Pipe thread EN 10226 Rp {{frac|2|1|2}}

The terminology for the use of ''G'' and ''R'' originated from Germany (''G'' for ''gas'', as it was originally designed for use on gas pipes; ''R'' for ''rohr'', meaning ''pipe''.)

==Pipe and fastener dimensions==

{| class=wikitable
|-
! rowspan=2            | G&nbsp;/&nbsp;R<br>size
! rowspan=2            | {{abbr|Typ.|Typical}} nut <br />sizes
! colspan=4            | Corresponding pipe
|-
! scope="col" | {{abbr|DN|Nominal diameter}}
! scope="col" | {{abbr|OD|Outside diameter}}
! scope="col" | Wall
|-
! scope="col" | {{small|(in)}}
! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(mm)}}
! scope="col" | {{small|(mm)}}
|- align="right"
| align="center" | {{frac|1|16}}
|
| 3
|
|
|- align="right"
| align="center" | {{frac|1|8}}
| 15
| 6
| 10.2
| 2
|- align="right"
| align="center" | {{frac|1|4}}
| 19
| 8
| 13.5
| 2.3
|- align="right"
| align="center" | {{frac|3|8}}
| 22 or 23
| 10
| 17.2
| 2.3
|- align="right"
| align="center" | {{frac|1|2}}
| 27
| 15
| 21.3
| 2.6
|- align="right"
| align="center" | {{frac|3|4}}
| 32
| 20
| 26.9
| 2.6
|- align="right"
| align="center" | 1
| 43
| 25
| 33.7
| 3.2
|- align="right"
| align="center" | {{frac|1|1|4}}
| 53
| 32
| 42.4
| 3.2
|- align="right"
| align="center" | {{frac|1|1|2}}
| 57
| 40
| 48.3
| 3.2
|- align="right"
| align="center" | 2
| 70
| 50
| 60.3
| 3.6
|- align="right"
| align="center" | {{frac|2|1|2}}
|
| 65
| 76.1
| 3.6
|- align="right"
| align="center" | 3
|
| 80
| 88.9
| 4
|- align="right"
| align="center" | 4
|
| 100
| 114.3
| 4.5
|- align="right"
| align="center" | 5
|
| 125
| 139.7
| 5
|- align="right"
| align="center" | 6
|
| 150
| 168.3
| 5
|}

== ISO 7 (Pressure Tight threads)==
The standard '''ISO 7 - Pipe threads where pressure-tight joints are made on the threads''' consists of the following parts:
* ISO 7-1:1994 Dimensions, tolerances and designation
* ISO 7-2:2000 Verification by means of limit gauges

== ISO 228 (Non Pressure Tight Threads)==
The standard '''ISO 228 - Pipe threads where pressure-tight joints are not made on the threads''' consists of the following parts:
* ISO 228-1:2000 Dimensions, tolerances and designation
* ISO 228-2:1987 Verification by means of limit gauges

==See also==
{{colbegin}}
* [[Engineering:AN thread|AN thread]]
* British standard brass thread
* [[Engineering:British Standard Whitworth|British Standard Whitworth]]
* [[Engineering:Garden hose#Standards and connectors|Garden hose thread]]
* [[Engineering:National pipe thread|National pipe thread]]
* [[Engineering:Panzergewinde|Panzergewinde]]
* [[Engineering:Thread angle|Thread angle]]
* [[Engineering:Threaded pipe|Threaded pipe]]
{{colend}}

==References==
{{Reflist}}

== External links ==
*[http://www.amesweb.info/Screws/British-Standard-Pipe-Parallel-Thread-BSPP.aspx British Standard Pipe Parallel Thread Dimensions]
*[http://www.amesweb.info/Screws/BSPT-Thread-Sizes-Dimensions.aspx British Standard Pipe Taper Thread Dimensions] {{Webarchive|url=https://web.archive.org/web/20170927115930/http://www.amesweb.info/Screws/BSPT-Thread-Sizes-Dimensions.aspx |date=2017-09-27 }}
*[https://www.ryco.com.au/technical/thread-connector-guides/bspt-bspp-threads/ BSP Thread Charts and Diagrams], showing dimensions of tubing and fittings
*[https://www.iso.org/standard/20819.html ISO 7-1:1994]
*[https://www.iso.org/standard/20820.html ISO 7-2:2000]
*[https://www.iso.org/standard/33777.html ISO 228-1:2000]
*[https://www.iso.org/standard/4104.html ISO 228-2:1987]
*[https://www.threadspecification.com/g/ Parallel pipe threads G]
*[https://www.threadspecification.com/pf/ Parallel pipe threads PF]

{{ISO standards}}

[[Category:Thread standards]]
[[Category:Piping]]
[[Category:Plumbing]]

{{Sourceattribution|British Standard Pipe}}