The 12-bit ND812, produced by Nuclear Data, Inc., was a commercial minicomputer developed for the scientific computing market.
Nuclear Data introduced it in 1970 at a price under $10,000[1] (equivalent to about $70,000 in 2019[2]).
Description
ND812 registers
|
0
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
(bit position)
|
Main accumulators
|
J
|
J accumulator
|
K
|
K accumulator
|
Sub-accumulators
|
R
|
R accumulator
|
S
|
S accumulator
|
Program counter
|
PC
|
Program Counter
|
Status flags
|
|
O
|
|
Overflow bit
|
|
F
|
Flag bit
|
Internal registers (not accessible by code)
|
IR
|
Instruction register
|
MR
|
Memory register
|
MAR
|
Memory address register
|
|
The architecture has a simple programmed I/O bus, plus a DMA channel.
The programmed I/O bus typically runs low to medium-speed peripherals, such as printers,
teletypes, paper tape punches and readers, while DMA is used for cathode ray tube
screens with a light pen, analog-to-digital converters, digital-to-analog converters,
tape drives, disk drives.
The word size, 12 bits, is large enough to handle unsigned integers from 0 to 4095 –
wide enough for controlling simple machinery. This is also enough to handle signed numbers from -2048 to +2047.
This is higher precision than a slide rule or most analog computers. Twelve bits could also store two
six-bit characters (note, six-bit isn't enough for two cases, unlike "fuller" ASCII
character set). "ND Code" was one such 6-bit character encoding that included upper-case alphabetic, digit,
a subset of punctuation and a few control characters.[3]
The ND812's basic configuration has a main memory of 4,096 twelve-bit words
with a 2 microsecond cycle time. Memory is expandable to 16K words in 4K word increments. Bits within the word
are numbered from most significant bit (bit 11) to
least significant bit (bit 0).
The programming model consists of four accumulator registers: two main accumulators, J and K,
and two sub accumulators, R and S. A rich set of arithmetic and logical operations are provided for the
main accumulators and instructions are provided to exchange data between the main and sub accumulators.
Conditional execution is provided through "skip" instructions. A condition is tested and the subsequent
instruction is either executed or skipped depending on the result of the test. The subsequent instruction
is usually a jump instruction when more than one instruction is needed for the case where the test fails.
Input/Output
The I/O facilities include programmable interrupts with 4-levels of priority that can trap to any location in
the first 4K words of memory. I/O can transmit 12 or 24 bits, receive 12 or 24 bits, or transmit and receive
12 bits in a cycle. I/O instructions include 4 bits for creating pulses for peripheral control. I/O peripherals
can be attached via 76 signal connector that allows for direct memory access by peripherals.
DMA is accomplished by "cycle stealing" from the CPU to store words directly into
the core memory system.
Nuclear Data provided interfaces to the following peripherals:
- Bulk storage devices
- Diablo Model 31 standard density disk cartridge
- Diablo Model 31 high density disk cartridge
- EDP fixed-head disk models 3008, 3016, 3032, 3064, or 3120
- Magnetic tape I/O devices
- Magnetic cassette tape
- PEC 7-track magnetic tape
- PEC 9-track magnetic tape
- Paper tape I/O devices
- Superior Electric Model TRP125-5 photoelectric tape reader (125 char/sec)
- Dataterm Model HS300 photoelectric tape reader (300 char/sec)
- Remex Model RPF1150B photoelectric tape reader (200 char/sec)
- Remex Model RPF1075B mylar tape punch (75 char/sec)
- Tally Model 1504 paper tape reader (60 char/sec)
- Tally Model 1505 paper tape punch (60 char/sec)
- Teletype Model BRPE11 paper tape punch (110 char/sec)
- Hard copy I/O devices
- Data Products Model 2410 line printer
- Centronics Model 101 line printer (165 char/sec)
- Franklin Model 1220 printer (20 lines/sec)
- Franklin Model 1230 printer (30 lines/sec)
- Hewlett-Packard Model 5050A printer (20 lines/sec)
- Hewlett-Packard Model 5055A printer (10 lines/sec)
- Calcomp digital incremental plotter
Programming facilities
The ND812 did not have an operating system, just a front panel and run and halt switches.
The I/O facility allowed for peripherals to directly load programs into memory while the computer
was halted and not executing instructions. Another option was to enter a short loader program
that would be used to bootstrap the desired program from a peripheral such as a teletype or
paper tape reader. Since core memory is non-volatile, shutting off the computer did not result
in data or program loss.
A number of system programs were made available by Nuclear Data for use with the ND812: BASC-12
assembler, symbolic text editor, NUTRAN interpreter, and disk-based symbolic text editor,
BASC-12 Assembler
An assembler called BASC-12 was provided. BASC-12 was a two-pass assembler,
with an optional third pass. Pass one generates a symbol table, pass two produces a
binary output tape and pass three provides a listing of the program.
A sample of the assembler from the Principles of Programming the ND812 Computer manual
is shown below:
/Input two unequal numbers "A" and "B", compare the two numbers
/and determine which is larger, and output a literal statement
/"A > B", or "B > A" as applicable.
/
/Input and store values for A & B
*200
Start, TIF /Clear TTY flag
JPS Input /Get value for A
STJ A
JPS Input /Get value for B
STJ B
/
/Determine which of the two values is larger
LDJ A
SBJ B /Subtract B from A
SIP J /Test for A positive
JMP BRAN /No! B > A
LDJ ABCST /Yes! A > B
SKIP /Skip next instruction
BRAN, LDJ BACST
/
/Set up and output expression
/
JPS OUT
STOP
JMP START
/
/Working or data storage area
/
A, 0 /Constant A
B, 0 /Constant B
ABCST, AB /Address of A > B literal
BACST, BA /Address of B > A literal
C260, 260 /ASCII zone constant
/
/Input routine + ASCII zone strip
/
Input, 0 /Entry point
TIS
JMP .-1
TRF
TCP /Echo input at teletype
TOS
JMP .-1
SBJ C260
JMP@ INPUT
/
/Output routine - Output ASCII expression
/
Out, 0 /Entry point
STJ LOOP+1
LDJ C5 /Set number of character constant
STJ CTR
/
/Output data loop
/
Loop, TWLDJ
0
TCP
TOS
JMP .-1
ISZ LOOP+1
DSZ CTR /Test for all characters out
JMP LOOP /No
JMP@ Out /Return
C5, 5
CTR, 0
/
/Output messages
/
AB, 215
212
301 /A
276 />
302 /B
BA, 215
212
302 /B
276 />
301 /A
$ /End character
NUTRAN
NUTRAN, a conversational, FORTRAN-like language, was provided. NUTRAN was intended for
general scientific programming. A sample of NUTRAN is shown below:
1 PRINT 'INPUT VALUES FOR X AND Y'
2 INPUT X,Y
3 Z=X+Y
4 PRINT 'X+Y= ',Z
5 STOP
An example of the conversational nature of NUTRAN is shown below. >
is the command prompt
and :
is the input prompt.
>1.G
INPUT VALUES FOR X AND Y
:3
:2
X+Y= .5000000E 1
>
Instruction formats
The instruction set consists of single and double word instructions.
Operands can be immediate, direct or indirect. Immediate operands are
encoded directly in the instruction as a literal value. Direct operands
are encoded as the address of the operand. Indirect operands encode the
address of the word containing a pointer to the operand.
Single word instructions
0
|
|
|
3
|
4
|
5
|
6
|
|
|
|
|
11
|
Operation
|
D/I
|
+/-
|
Displacement
|
The displacement and sign bit allow single word instructions to address locations between
-63 and +63 of the location of the instruction. Bit 4 of the instruction allows for a
choice between indirect and direct addressing. When the displacement is used as an
indirect address, the contents of the location which is +/-63 locations from the instruction
location is used as a pointer to the actual operand.
Many single word instructions do not reference memory and use bits 4 and 5 as part of the
specification of the operation.
Literal format
0
|
|
|
3
|
4
|
5
|
6
|
|
|
|
|
11
|
Operation
|
Instruction
|
Literal
|
Group 1 Format
0
|
|
|
3
|
4
|
5
|
6
|
7
|
8
|
|
|
11
|
0010
|
K
|
J
|
Shift Rotate
|
Shift Count
|
Group 1 instructions perform arithmetic, logical, exchange and shifting functions
on the accumulator registers. This includes hardware multiply and divide instructions.
Bit 4 is set if the K register is affected. Bit 5 is set if the J register is affected.
Both bits are set of both registers are affected.
Group 2 format
0
|
|
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
0011
|
K
|
J
|
OV
|
Comp Set
|
Comp Clear
|
0 1
|
>= 0 < 0
|
!= 0 != 0
|
Group 2 format instructions test for internal conditions of the J and K
accumulator registers, manipulate the overflow and flag status bits and
provide complement, increment and negation operations on the J and K accumulator
registers. Bits 9, 10 and 11 select the condition to be tested.
Two word instructions
0
|
|
2
|
3
|
|
|
6
|
7
|
8
|
9
|
10
|
11
|
Operation
|
Instruction
|
Ind
|
KJ Acc.
|
Change Fields
|
MF1
|
MF2
|
Absolute 12-bit Address
|
Bit 9, Change Fields, inhibits the absolute address from referencing a different field than
the one containing the instruction. When bit 8 is 1, the upper accumulator K is used with
the instruction, otherwise the lower accumulator J is used. When bit 7 is 1, indirect
addressing is used, otherwise direct addressing is used.
Status Word format
0
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
Flag
|
Overflow
|
JPS
|
Int
|
IONL
|
IONA
|
IONB
|
IONH
|
Current Execution
|
|
MF0
|
MF1
|
MF1
|
MF2
|
|
MF1
|
MF2
|
The status register doest not exist as a distinct register. It is the contents
of several groups of indicators that are all stored in the J register when
desired. The JPS and Int bits hold the current field contents that would
be used during a JPS instruction or interrupt. The flag and overflow bits
can be set explicitly from the J register contents with the RFOV instruction,
but the other bits must be set by distinct instructions.
Subroutines
The ND812 processor provides a simple stack for operands, but
doesn't use this mechanism for storing subroutine return addresses. Instead, the return
address is stored in the target of the JPS
instruction and then the PC
register is updated to point to the location following the stored return address. To
return from the subroutine, an indirect jump through the initial location of the
subroutine restores the program counter to the instruction following the JPS
instruction.
Instruction set
Memory reference instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
ANDF |
2000 |
AND with J, Forward |
J
|
LDJ |
5000 |
Load J |
J
|
TWLDJ |
0500 |
Load J |
J
|
STJ |
5400 |
Store J |
Memory
|
TWSTJ |
0540 |
Store J |
Memory
|
TWLDK |
0510 |
Load K |
K
|
TWSTK |
0550 |
Store K |
Memory
|
ADJ |
4400 |
Add to J |
J, OV
|
TWADJ |
0440 |
Add to J |
J, OV
|
SBJ |
4000 |
Subtract from J |
J, OV
|
TWSBJ |
0400 |
Subtract from J |
J, OV
|
TWADK |
0450 |
Add to K |
K, OV
|
TWSBK |
0410 |
Subtract from K |
K, OV
|
ISZ |
3400 |
Increment memory and skip if zero |
Memory, PC
|
TWISZ |
0340 |
Increment memory and skip if zero |
Memory, PC
|
DSZ |
3000 |
Decrement memory and skip if zero |
Memory, PC
|
TWDSZ |
0300 |
Decrement memory and skip if zero |
Memory, PC
|
SMJ |
2400 |
Skip if memory not equal to J |
PC
|
TWSMJ |
0240 |
Skip if memory not equal to J |
PC
|
TWSMK |
0250 |
Skip if memory not equal to K |
PC
|
JMP |
6000 |
Unconditional jump |
PC
|
TWJMP |
0600 |
Unconditional jump |
PC
|
JPS |
6400 |
Jump to subroutine |
Memory, PC
|
TWJPS |
0640 |
Jump to subroutine |
Memory, PC
|
XCT |
7000 |
Execute instruction |
|
Logical operations
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
AND J |
1100 |
Logical AND J,K into J |
J
|
AND K |
1200 |
Logical AND J,K into K |
K
|
AND JK |
1300 |
Logical AND J,K into J,K |
J, K
|
Arithmetic operations on accumulators
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
AJK J |
1120 |
(J + K) to J |
J, OV
|
NAJK J |
1130 |
-(J + K) to J |
J, OV
|
SJK J |
1121 |
(J - K) to J |
J, OV
|
NSJK J |
1131 |
-(J - K) to J |
J, OV
|
ADR J |
1122 |
(R + J) to J |
J, OV
|
NADR J |
1132 |
-(R + J) to J |
J, OV
|
ADS J |
1124 |
(S + J) to J |
J, OV
|
NADS J |
1134 |
-(S + J) to J |
J, OV
|
SBR J |
1123 |
(R - J) to J |
J, OV
|
NSBR J |
1133 |
-(R - J) to J |
J, OV
|
SBS J |
1125 |
(S - J) to J |
J, OV
|
NSBS J |
1135 |
-(S - J) to J |
J, OV
|
AJK K |
1220 |
(J + K) to K |
K, OV
|
NAJK K |
1230 |
-(J + K) to K |
K, OV
|
SJK K |
1221 |
(J - K) to K |
K, OV
|
NSJK K |
1231 |
-(J - K) to K |
K, OV
|
ADR K |
1222 |
(R + K) to K |
K, OV
|
NADR K |
1232 |
-(R + K) to K |
K, OV
|
ADS K |
1224 |
(S + K) to K |
K, OV
|
NADS K |
1234 |
-(S + K) to K |
K, OV
|
SBR K |
1223 |
(R - K) to K |
K, OV
|
NSBR K |
1233 |
-(R - K) to K |
K, OV
|
SBS K |
1225 |
(S - K) to K |
K, OV
|
NSBS K |
1235 |
-(S - K) to K |
K, OV
|
AJK JK |
1320 |
(J + K) to J,K |
J, K, OV
|
NAJK JK |
1330 |
(J + K) to J,K |
J, K, OV
|
SJK JK |
1321 |
(J - K) to J,K |
J, K, OV
|
NSJK JK |
1331 |
-(J - K) to J,K |
J, K, OV
|
MPY |
1000 |
Multiply J by K into R, S |
J, K, R, S, OV
|
DIV |
1001 |
Divide J,K by R into J, K |
J, K, R, S, OV
|
Shift/rotate instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
SFTZ J |
1140 |
Shift J left N |
J
|
SFTZ K |
1240 |
Shift K left N |
K
|
SFTZ JK |
1340 |
Shift J,K left N |
J, K
|
ROTD J |
1160 |
Rotate J left N |
J
|
ROTD K |
1260 |
Rotate K left N |
K
|
ROTD JK |
1360 |
Rotate J,K left N |
J,K
|
Load and exchange operations
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
LJSW |
1010 |
Load J from switch register |
J
|
LRF J |
1101 |
Load R from J |
R
|
LJFR |
1102 |
Load J from R |
J
|
EXJR |
1103 |
Exchange J and R |
J, R
|
LSFK |
1201 |
Load S from K |
S
|
LKFS |
1202 |
Load K from S |
K
|
EXKS |
1203 |
Exchange K and S |
K, S
|
LKFJ |
1204 |
Load K from J |
K
|
EXJK |
1374 |
Exchange J and K |
J, K
|
LRSFJK |
1301 |
Load R, S from J, K |
R, S
|
LJKFRS |
1302 |
Load J, K from R, S |
J, K
|
EXJRKS |
1303 |
Exchange J, K and R, S |
J, K, R, S
|
LJST |
1011 |
Load status register into J |
J
|
RFOV |
1002 |
Read Flag, OV from J |
J
|
Conditional skips
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
SIZ J |
1505 |
Skip if J equals zero |
PC
|
SIZ K |
1605 |
Skip if K equals zero |
PC
|
SIZ JK |
1705 |
Skip if both J and K equals zero |
PC
|
SNZ J |
1501 |
Skip if J not equal zero |
PC
|
SNZ K |
1601 |
Skip if K not equal zero |
PC
|
SNZ JK |
1701 |
Skip if J or K not equal zero |
PC
|
SIP J |
1501 |
Skip if J positive |
PC
|
SIP K |
1602 |
Skip if K positive |
PC
|
SIP JK |
1702 |
Skip if both J and K positive |
PC
|
SIN J |
1506 |
Skip if J negative |
PC
|
SIN K |
1606 |
Skip if J negative |
PC
|
SIN JK |
1706 |
Skip if both J and K negative |
PC
|
Clear, complement, increment and set
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
CLR J |
1510 |
Clear J |
J
|
CLR K |
1610 |
Clear K |
K
|
CLR JK |
1710 |
Clear J, K |
J, K
|
CMP J |
1520 |
Complement J |
J
|
CMP K |
1620 |
Complement K |
K
|
CMP JK |
1720 |
Complement J, K |
J, K
|
SET J |
1530 |
Set J to -1 |
J
|
SET K |
1630 |
Set K to -1 |
K
|
SET JK |
1730 |
Set J, K to -1 |
J, K
|
Overflow bit instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
SIZ O |
1445 |
Skip if overflow zero |
PC
|
SNZ O |
1441 |
Skip if overflow set |
PC
|
CLR O |
1450 |
Clear overflow |
OV
|
CMP O |
1460 |
Complement overflow |
OV
|
SET O |
1470 |
Set overflow |
OV
|
Flag bit instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
SIZ |
1405 |
Skip if flag zero |
PC
|
SNZ |
1401 |
Skip if flag set |
PC
|
CLR |
1410 |
Clear flag |
F
|
CMP |
1420 |
Complement flag |
F
|
SET |
1430 |
Set flag |
F
|
Increment and negate
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
INC J |
1504 |
Increment J |
J
|
INC K |
1604 |
Increment K |
K
|
INC JK |
1704 |
Increment J, K |
J, K
|
NEG J |
1524 |
Negate J |
J
|
NEG K |
1624 |
Negate K |
K
|
NEG JK |
1724 |
Negate J, K |
J, K
|
Interrupt instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
IONH |
1004 |
Enable interrupt level H |
|
IONA |
1006 |
Enable interrupt level A, H |
|
IONB |
1005 |
Enable interrupt level B, H |
|
IONN |
1007 |
Enable all interrupt levels |
|
IOFF |
1003 |
Disable all interrupts |
|
Powerfail logic instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
PION |
1500 |
Powerfail on |
|
PIOF |
1600 |
Powerfail off |
|
SKPL |
1440 |
Skip on power low |
PC
|
Literal instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
ANDL |
2100 |
AND literal with J |
J
|
ADDL |
2200 |
Add literal to J |
J
|
SUBL |
2300 |
Subtract literal from J |
J
|
INT and JPS register instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
LDREG |
7720 |
Load JPS from J, INT from K |
|
LDJK |
7721 |
Load JPS to J, INT to K |
J, K
|
RJIB |
7722 |
Set JPS and INT status |
|
Teletype system
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
TIS |
7404 |
Skip if keyboard ready |
PC
|
TIR |
7402 |
Load keyboard into J |
J
|
TIF |
7401 |
Keyboard-reader fetch |
|
TRF |
7403 |
Keyboard read-fetch |
J
|
TOS |
7414 |
Skip if printer-punch ready |
PC
|
TOC |
7411 |
Clear flag |
|
TCP |
7413 |
Clear flag, print-punch |
|
TOP |
7412 |
Print-punch |
|
High-Speed paper tape
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
HIS |
7424 |
Skip HS reader ready |
PC
|
HIR |
7422 |
Clear flag; read HS buffer |
J
|
HIF |
7421 |
HS reader fetch |
|
HRF |
7423 |
HS reader read-fetch |
J
|
HOS |
7434 |
Skip if HS punch ready |
PC
|
HOL |
7432 |
Clear flag; load buffer from J |
|
HOP |
7431 |
Punch on HS punch |
|
HLP |
7433 |
Load and punch HS punch |
|
Magnetic cassette tape system
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
CSLCT1 |
7601 |
Place cassette 1 on-line |
|
CSLCT2 |
7602 |
Place cassette 2 on-line |
|
CSLCT3 |
7604 |
Place cassette 3 on-line |
|
CSTR |
0740, 0124 |
Selected TWIO skip if transport ready |
PC
|
CSFM |
0740, 0104 |
Skip on filemark |
PC
|
CSET |
0740, 0110 |
Skip if transport at end of tape |
PC
|
CSNE |
0740, 0122 |
Skip if no error |
PC
|
CSBT |
0740, 0130 |
Skip if transport at beginning of tape |
PC
|
CCLF |
0740, 0141 |
Clear all cassette control flags |
|
CWFM |
0740, 0151 |
Write file mark |
|
CSWR |
0740, 0152 |
Skip if write ready |
PC
|
CWRT |
0740, 0154 |
Write J into buffer |
|
CSRR |
0740, 0142 |
Skip if ready |
PC
|
CRDT |
0740, 0144 |
Read buffer into J |
J
|
CHSF |
0740, 0101 |
High speed forward to EOT |
|
CSPF |
0740, 0102 |
Space forward to filemark |
|
CHSR |
0740, 0121 |
High-speed reverse to BOT |
|
Miscellaneous instructions
Assembler Mnemonic |
Octal Code |
Description |
Registers Affected
|
STOP |
0000 |
Stop execution |
|
SKIP |
1442 |
Unconditional skip |
PC
|
IDLE |
1400 |
One cycle delay |
|
TWIO |
0740 |
Two-word I/O |
|
References
External links
![Public domain Public domain](/wiki/images/thumb/e/ef/Imbox_license.svg/52px-Imbox_license.svg.png) | Original source: https://en.wikipedia.org/wiki/ND812. Read more |