Engineering:WD-11
The WD-11 vacuum tube, a triode, was introduced by the Westinghouse Electric corporation in 1922 for their Aeriola RF model radio and found use in other contemporary regenerative receivers (used as a detector-amplifier) including the Regenoflex and Radiola series. The WD11 and "RCA-11"[1] (and later simply named "11" by RCA[2] and Philips/Miniwatt[3]) have the following characteristics:
| Socket: | UV4 (also known as WD-4-Pin) | |
|---|---|---|
| EIA/RETMA Base Diagram: | 4F | |
| Description: | Detector Amplifier Triode | |
| Filament: | Directly heated 1.1 V | 0.25 A |
| Plate (anode) Voltage: | 90V | 135V maximum |
| Grid Voltage: | -4.5V | -10.5V |
| Plate Current | 2.5 mA | 3.0 mA |
| Plate Resistance: | 15.5 kilohms | 15 kilohms |
| Amplification Factor (mu): | 6.6 | 6.6 |
| Transconductance (gm or S): | 0.425 mA/V | 0.44 mA/V |
| Power Output: (Po): | 0.007 W | 0.04 W[4] |
| Grid-plate Capacitance (Cga): | 3.3 pF | |
- ↑ RCA Receiving Tube Manual RC-13. 1937. p. 98.
- ↑ RCA Receiving Tube Manual RC-14. 1940. p. 157.
- ↑ "Miniwatt" Technical Data (6th ed.). Australia: The "Miniwatt" Electronics Division of Philips Electrical Industries Pty. Limited, N.S.W.. 1958. p. 56.
- ↑ "WD 11". http://oldradio.qrz.ru/tubes/foreign/03/WD11.gif. Retrieved 7 January 2013.
Drawbacks
The WD-11's design was somewhat ill thought out, when the filament burns out it has a tendency to contact the plate, feeding high voltages back through the heater circuitry and subsequently burning out the filaments on the remaining tubes,. The WD-11 also has a unique 4 pin base layout that was unlike any subsequent UV and UX style tube base. It had 3 "small" pins and one "large" pin. (Later UV based tubes relied on an index pin on the side of the tube base and UX tubes had 2 large and 2 small pins to ensure proper indexing.)
It was replaced just a year later by higher performance tubes which were less likely to encounter the filament shorting problem, Westinghouse Electric's WD-12 and General Electric's UX-199. No radios using the WD-11 tube were designed after 1924, RCA ceased production and issued a service bulletin describing how to retrofit existing sets to use the newer UX-199 triodes.
Collectiblity
Because of its rarity it has become one of the most valuable vacuum tubes in the world. New-old-stock units have sold for as much as US$180 and used tubes for over $100, more than the original price of the radios that use them. Collectors rarely, if ever use these tubes for fear of burning them out.[citation needed]
Substitution
Sets that use the costly WD-11 and UV-199 tubes can be modified to use the 1A5/GT octal power pentode (Which cost around $2.50) by wiring a 5.1 ohm resistor between the pins of the filament and fabricating an octal-to-four pin adaptor. The pin for the 1A5's suppressor is left unconnected and the screen connected to the plate.
The type 12 (also known as RCA-12) is electrically identical to the type 11, but with a more common UX4 base.
External links
Here is a link on how to modify other tubes to use in place of a wd11:
 |  |
