Administrative distance

Short description: Number of arbitrary unit used in network routing decisions

Administrative distance (AD) or route preference is a number of arbitrary unit assigned to dynamic routes, static routes and directly-connected routes. The value is used in routers to rank routes from most preferred (low AD value) to least preferred (high AD value). When multiple paths to the same destination are available in its routing table, the router uses the route with the lowest administrative distance.

Router vendors typically design their routers to assign a default administrative distance to each kind of route. For example, on Cisco routers, routes issued by the Open Shortest Path First routing protocol have a lower default administrative distance than routes issued by the Routing Information Protocol. This is because, by default on Cisco routers, OSPF has a default administrative distance of 110 and RIP has a default administrative distance of 120. Administrative distance values can, however, usually be adjusted manually by a network administrator.

Overview

The administrative distance (AD) value is assigned by the router on a per-protocol basis. Routers, by design, should not install multiple routes into the routing table as this has the potential to cause routing loops. While a router may run multiple routing protocols on the same device, it is necessary for the router to implement a process to ensure that multiple routes, pointing to the same destination do not simultaneously exist in the routing table. Each process running on a router advertises its administrative distance value to the local router. The router uses this value to determine which route should be used. Once a route has been selected, the routing information database is updated. If two routes have the same administrative distance, the router uses its vendor-specific algorithm to determine which route should be installed. Cisco routers simply ignore the values and fall back to the default values, which are never the same.

The router will usually compare administrative distances to determine which protocol has the lowest value. The router prefers protocols that have a lower assigned administrative distance. For example, OSPF has a default distance of 110, so it is preferred by the router process, over RIP, which has a default distance of 190. The administrator can arbitrarily reconfigure the administrative distances, which affects the ranking of the preferred routes by the routing process. On Cisco routers, static routes have an administrative distance of 1, making them preferred over routes issued by a dynamic routing protocol. The administrative distance is a value that is always only referenced by the local router itself. The administrative distance is not advertised on the network.

Default administrative distances

Cisco

The following table lists the default administrative distances for various routing protocols used on Cisco routers.

Routing protocol	Administrative distance
Directly connected interface	0
Static route	1
Dynamic Mobile Network Routing (DMNR)	3
EIGRP summary route	5
External BGP	20
EIGRP internal route	90
IGRP	100
Open Shortest Path First (OSPF)	110
Intermediate System to Intermediate System (IS-IS)	115
Routing Information Protocol (RIP)	120
Exterior Gateway Protocol (EGP)	140
ODR	160
EIGRP external route	170
Internal BGP	200
Next Hop Resolution Protocol (NHRP)	250
Default static route learned via DHCP	254
Unknown and unused	255

Juniper

The following table lists the default administrative distances for various routing protocols used on Juniper routers.

Routing protocol	Administrative distance
Directly connected interface	0
Static routes	5
OSPF internal routes	10
IS-IS Level 1 Internal	15
IS-IS Level 2 Internal	18
RIP	100
Aggregate (route summary)	130
OSPF external routes	150
IS-IS Level 1 External	160
IS-IS Level 2 External	165
BGP	170

Extreme Networks

The following table lists the default administrative distances used on ExtremeXOS / Switch-Engine.

Routing protocol	Administrative distance
Directly connected	10
MPLS	20
Blackhole	50
Static	1100
HostMobility	1150
ICMP-Redirect	1200
Fabric	1699
eBGP	1700
iBGP	1900
OSPFintra	2200
OSPFinter	2300
IS-IS	2350
IS-IS L1	2360
IS-IS L2	2370
RIP	2400
OSPF AS Ext	3100
OSPF Ext1	3200
OSPF Ext2	3300
IS-IS L1 Ext	3400
IS-IS L2 Ext	3500
Bootp	5000

The following table lists the default administrative distances used on Extreme VOSS / Fabric-Engine.

Routing Protocol	Administrative distance
Local	0
Static	5
SPBm L1	7
OSPFintra	20
OSPFinter	25
eBGP	45
RIP	100
OSPF Ext1	120
OSPF Ext2	125
iBGP	175

Configuration

Cisco IOS

The network administrator may modify the administrative distance to change the desired ranking of router protocols. This may be necessary in cases where routing redistribution has to be used, otherwise, routing loops could occur. The Cisco Internetwork Operating System enables network administrators to modify the distance by changing the distance value in sub-router configuration mode. In the example below, RIP's administrative distance is changed to 89 so that it used in preference to OSPF.

R1#enable

R1#configure terminal

R1(config)#router rip

R1(config-router)#distance 89

Manually configuring the administrative distance is also required when configuring a floating static route. Floating static routes are used to provide an alternate path when a primary link fails. In order for static routes to be configured as a backup, the static route's administrative distance would need to be adjusted. Otherwise, it will take precedence over all routing protocols and routes issued from a routing protocol will not be inserted into the routing table. The example below shows how to configure the administrative distance to 254 to specify that it should only be used as a last resort.

R1(config)# ip route 10.0.0.0 255.0.0.0 backupLink 1 254

In the event that two routing protocols are configured with the same administrative distance, the Cisco router will ignore the configured values and instead use the default values.

Verifying the configuration of the administrative distance is done on Cisco equipment using the show ip route command in privileged exec mode on the console of the Cisco router. In the example shown below, the administrative distance is 1. The letter "S" indicates that the route is a static route that has, for all intents and purposes, been added manually to the router process by the administrator and installed into the routing table.

Router#enable

Router#configure terminal

Router(config)#ip route 1.1.1.0 255.255.255.0 fastEthernet 0/0

Router(config)#do show ip route

The do show ip route command will display the following, confirming that a static route has an administrative distance of 1.

S 1.1.1.0/0 [1/0] via 172.31.0.1

See also

• Metrics (networking), used for choosing a route when administrative distance is the same