Chemistry:Hummers' method
Hummers' method is a chemical process that can be used to generate graphite oxide through the addition of potassium permanganate to a solution of graphite, sodium nitrate, and sulfuric acid. It is commonly used by engineering and lab technicians as a reliable method of producing quantities of graphite oxide. It is also able to be revised in the creation of a one-atom-thick version of the substance known as graphene oxide.
Graphite oxide
Graphite oxide is a compound of carbon, oxygen, and hydrogen where there is a ratio between 2.1 and 2.9 of carbon to oxygen. Graphite oxide is typically a yellowish solid. It is also known as graphene oxide when used to form unimolecular sheets.
Method
Hummers' method[1] was developed in 1958 as a safer, faster and more efficient method of producing graphite oxide. Before the method was developed, the production of graphite oxide was slow and hazardous to make because of the use of concentrated sulfuric and nitric acid. The Staudenmeier–Hoffman–Hamdi method[2] introduced the addition of potassium chlorate. However, this method had more hazards and produced one gram of graphite oxide to ten grams of potassium chlorate.[3]
William S. Hummers and Richard E. Offeman created their method as an alternative to the above methods after noting the hazards they posed to workers at the National Lead Company. Their approach was similar in that it involved adding graphite to a solution of concentrated acid. However, they simplified it to just graphite, concentrated sulfuric acid, sodium nitrate, and potassium permanganate. They also did not have to use temperatures above 98 °C and avoided most of the explosive risk of the Staudenmeier–Hoffman–Hamdi method.
The procedure starts with 100 g graphite and 50 g of sodium nitrate in 2.3 liters of sulfuric acid at 66 °C which is then cooled to 0 °C. 300 g of potassium permanganate is then added to the solution and stirred. Water is then added in increments until the solution is approximately 32 liters.
The final solution contains about 0.5% of solids to then be cleaned of impurities and dehydrated with phosphorus pentoxide.
Chemical equations and efficiency
The basic chemical reaction involved in the Hummers' method is the oxidation of graphite, introducing molecules of oxygen to the pure carbon graphene. The reaction occurs between the graphene and the concentrated sulfuric acid with the potassium permanganate and sodium nitrate acting as catalysts. The process is capable of yielding approximately 188 g of graphite oxide to 100 g of graphite used. The ratio of carbon to oxygen produced is within the range of 1 to 2.1–2.9 that is characteristic of graphite oxide. The contaminants are determined to be mostly ash and water. Toxic gases such as dinitrogen tetraoxide and nitrogen dioxide are evolved in the process. The final product is typically 47.06% carbon, 27.97% oxygen, 22.99% water, and 1.98% ash with a carbon-to-oxygen ratio of 2.25. All of these results are comparable to the methods that preceded them.
| Method | % Carbon | % Oxygen | % Water | % Ash | Carbon-to-oxygen atomic ratio |
|---|---|---|---|---|---|
| Hummers | 47.06 | 27.97 | 22.99 | 1.98 | 2.25 |
| Staudenmeier | 52.112 | 23.99 | 22.2 | 1.90 | 2.89 |
Significance
The method has been taken up by many researchers and chemists who are interested in the use of graphite oxide for other purposes, because it is the fastest[4] conventional method of producing graphite oxide while maintaining a relatively high C/O ratio. When researchers and chemists are introducing a large quantity of graphite oxide within time limitations, Hummers' method is usually referenced in some form.
Modern variations
Graphite oxide captured the attention of the scientific community after the discovery of graphene in 2004. Many teams are looking into ways of using graphite oxide as a shortcut to mass production of graphene. So far, the materials produced by these methods have shown to have more defects than those produced directly from graphite. Hummers' method remains a key point of interest because it is an easy method of producing large quantities of graphite oxide.
Other groups have been focused on making improvements to the Hummers' method to make it more efficient and environmentally friendly. One such process is eliminating the use of NaNO3 from the process.[5][6] The addition of persufate (S2O82−) ensures the complete oxidation and exfoliation of graphite to yield suspensions of individual graphite oxide sheets. The elimination of nitrate is also advantageous as it stops the production of gases such as nitrogen dioxide and dinitrogen tetraoxide.
Future uses
Besides graphene, Hummers' method has become a point of interest in photocatalysts.[7] After discovering that graphite oxide is reactive to many of the wavelengths of light found within sunlight, teams have been looking into methods of using it to bolster the speed of reaction in decomposition of water and organic matter. The most common method for producing the graphite oxide in these experiments has been Hummers' method.
See also
- Graphite Oxide
References
- ↑ 1.0 1.1 Hummers, William S.; Offeman, Richard E. (March 20, 1958). "Preparation of Graphitic Oxide". Journal of the American Chemical Society 80 (6): 1339. doi:10.1021/ja01539a017.
- ↑ Ojha, Kasinath; Anjaneyulu, Oruganti; Ganguli, Ashok (10 August 2014). "Graphene-based hybrid materials: synthetic approaches and properties". Current Science 107 (3): 397–418. http://www.currentscience.ac.in/Volumes/107/03/0397.pdf. Retrieved 7 November 2014.
- ↑ Murray-Smith, Robert. "How to make graphene oxide". https://www.youtube.com/watch?v=lRDPZ8yLh04.
- ↑ Ciszewski, Mateusz; Mianowski, Andrzej (2013). "Survey of graphite oxidation methods using oxidizing mixtures in inorganic acids". Chemik 67 (4): 267–274. http://www.chemikinternational.com/year-2013/year-2013-issue-4/survey-of-graphite-oxidation-methods-using-oxidizing-mixtures-in-inorganic-acids/. Retrieved 15 November 2014.
- ↑ Kovtyukhova, N.I.; Ollivier, P.J.; Martin, B.J.; Mallouk, T.E.; Chizhik, S.A.; Buzaneva, E.V.; Gorchinskiy, A.D. (January 1999). "Layer-by-Layer Assembly of Ultrathin Composite Films from Micron-Size Graphite Oxide Sheets and Polycations". Chemistry of Materials 11 (3): 771–778. doi:10.1021/cm981085u.
- ↑ Chen, Ji; Yao, Bowen; Li, Chun; Shi, Gaoquan (November 2013). "An improved Hummers method for eco-friendly synthesis of graphene oxide". Carbon 64: 225–229. doi:10.1016/j.carbon.2013.07.055.
- ↑ Tu, Wenguang; Zhou, Yong; Zou, Zhigang (October 2013). "Versatile Graphene-Promoting Photocatalytic Performance of Semiconductors: Basic Principles, Synthesis, Solar Energy Conversion, and Environmental Applications". Advanced Functional Materials 23 (40): 4996–5008. doi:10.1002/adfm.201203547.
 |  |
