Company:Avcon

From HandWiki
Short description: American company
Avcon Corporation
IndustryAutomobile
HeadquartersFranklin, Wisconsin
ProductsCharging interfaces for battery electric vehicles
Websiteavconev.com[|permanent dead link|dead link}}]

Avcon is a company that manufactures charging interfaces for battery electric vehicles (EV).[1] The lettering convention is Avcon for the company and AVCON (capitals) for the EV charging connector.

History

Avcon belonged to the Maréchal Electric group of companies, which has its primary corporate headquarters in France.[2] Maréchal established the MELTRIC Corporation in 1981 to market products for North America;[3] MELTRIC, in turn, registered the trademark for Avcon Corporation in 1995. The initial registered address for Avcon was in Cudahy, Wisconsin.[4]

AVCON coupler system

Lua error in Module:Multiple_image at line 163: attempt to perform arithmetic on local 'totalwidth' (a nil value). The AVCON conductive interface was used by the Ford Ranger EV truck, Solectria, and the Honda EV Plus.[5]:22 The AVCON conductive EV charging coupler system consists of a rectangular charging connector (the male handle at the end of the electric vehicle supply equipment cable) which plugs into a vehicle inlet (the female receptacle) mounted on the vehicle.

The SAE J1772 "SAE Electric Vehicle Conductive Charge Coupler" recommended practice for surface vehicles was first issued in 1996, with the AVCON connector described in an appendix.[5]:25 [6] Maréchal designed the initial coupler with butt connectors, which included 11 contacts overall, two of which were DC contacts for Level 3 charging (as defined in article 625 of the 1999 version of the National Electric Code).[7] The November 2001 version of SAE J1772 moved the AVCON connector into the main body, making it the default connector in North America; the revised version of the AVCON connector has six contacts, dropping support for Level 3 charging.

The AVCON coupler was succeeded in the 2009 edition of SAE J1772 by a round keyed coupler designed by Yazaki.[8] American and Japanese plug-in electric vehicles that came to market starting in 2011 such as the Chevrolet Volt and Nissan Leaf use the Yazaki coupler specified in the 2009 revision of SAE J1772 for level 2 charging. The J1772(2009) coupler is also listed as the Type 1 coupler in the IEC 62196-2 AC charging standard, and the AVCON coupler is now deprecated.

Conductive and inductive charging systems

Public charging stations near LAX. The two 6 kW AC charging stations reflect the CARB mandate to include both connector types: the inductive Magne-charge gen2 SPI ("small paddle", left) and the conductive EVII ICS-200 AVCON (right).

The AVCON conductive interface was the primary competitor to the Magne Charge inductive charging paddle used by the General Motors EV1 and Chevy S10 EV, plus the 2002 Toyota RAV4 EV. Ford and Honda chose AVCON as a more cost effective EV charging solution to transfer the same 6KW AC power to the EV's on-board charging system (208 to 240 VAC, 40 amp circuit into the charging head).[citation needed]

Many public EV charging installations funded by the California Air Resources Board (CARB) – money came from DMV fees – were required to have both an inductive and a conductive AVCON charging head. This meant twice as much money was spent because the simple, cost-effective AVCON was not adopted by all automakers.[citation needed] These public EV charging installations did not use Avcon model charging heads; they used the more expensive EVII ICS-200 model AVCON charging heads.

Automakers abandoned their promise to CARB to produce production EVs for public purchase by using a CARB mandate loophole (selling slow neighborhood EVs or carts to obtain their CARB credits) and very few production EVs were actually sold to the public (either inductive or conductive).[citation needed]

Success of the conductive system

An experiment co-sponsored by the Electric Power Research Institute (EPRI) and conducted by Underwriters Laboratories during the development of SAE J1772 concluded that butt-type contacts outperformed other conductive contact types, including pin-and-sleeve contacts, for the environmental endurance testing phase.[9]

In 2001, AVCON was endorsed by the California Air Resources Board (CARB) over Magne Charge,[10] which caused GM to retire inductive paddle technology in 2002.[11]

Since conductive EV charging AVCONs can be used by all EVs by using an AVCON adapter box that provides a 240 V NEMA 14–50 outlet, and inductive EV charging cannot, some RAV4 EV drivers have taken to bringing their SPI TAL inductive charger with them. This allows RAV4 EVs with an inductive charging system to recharge from public, conductive, AVCON EV charging heads. This practice will fade away since virtually all 2011 and later production Electric Vehicles are equipped with a SAE J1772 charge port. Drivers of the few 2011 and later or conversion vehicles are either using SAE J1772 adapters that connect to their chargers or are putting SAE J1772 charge ports in their vehicles.[12]

Current status

With no current production EVs available using the AVCON standard, hosts of EV charging stations (such as Costco, shopping malls, etc.) providing electricity at no or little charge to the consumer withdrew their support to repair their public AVCON EV charging stations. Members of the Electric Auto Association, a 501.3c nonprofit, have set up funds soliciting public donations for EV charging so the charging stations can be repaired after vandals damage them. This keeps the EVs on the road by extending their range for very little electricity cost to the host.

AVCON stations are being converted to the round (Yazaki) SAE J1772 (2009) connector or phased out starting in 2011. In general, the conversion process is largely mechanical, consisting of replacing the AVCON connector with a Yazaki connector, as the signaling protocols are similar.[13]

See also

References

  1. ↑ "Avcon Corporation". 2007-09-11. Archived from the original on 2010-03-12. https://web.archive.org/web/20100312013907/http://www.avconev.com/. Retrieved 2010-05-31. 
  2. ↑ "L'EV Plug Alliance annonce l'adhésion de nouveaux membres et ses premiers produits disponibles" [The EV Plug Alliance announces new members and its first products] (PDF) (Press release) (in français). EV Plug Alliance. 20 September 2010. Retrieved 6 September 2021.
  3. ↑ "Global Presence". https://marechal.com/en/p-global-presence.html. 
  4. ↑ "Avcon Corporation, US Serial Number 74511656". https://tsdr.uspto.gov/#caseNumber=74511656&caseSearchType=US_APPLICATION&caseType=DEFAULT&searchType=statusSearch. 
  5. ↑ 5.0 5.1 Staff Report: Initial Statements of Reasons (Report). California Air Resources Board. May 11, 2001. https://ww2.arb.ca.gov/sites/default/files/barcu/regact/charger/isor.pdf. Retrieved 2 September 2021. 
  6. ↑ "SAE J1772 Overview based on the OLD 2001 version of SAE J1772". Modular EV Power LLC. 2009. http://modularevpower.com/Charging%20Station/1772.htm. 
  7. ↑ "EV Inlet Standard, P/N 55-28064". AVCON Corporation. July 6, 1994. http://www.partsonsale.com/avconschematcs1.html. 
  8. ↑ "Section 1962.2 Electric Vehicle Charging Requirements (DRAFT)". California Air Resources Board. July 16, 2008. https://www.arb.ca.gov/msprog/zevprog/hevtest/071608evchargingreq.pdf. 
  9. ↑ Hart, McMurphy & Parks; Underwriters Laboratories (October 1995). Contact Selection for Conductive Coupling of Electric Vehicle Charging Equipment, TR 105608 (Report). Electric Power Research Institute. https://www.epri.com/research/products/TR-105608. Retrieved 6 September 2021. 
  10. ↑ "ARB Amends ZEV Rule: Standardizes Chargers & Addresses Automaker Mergers" (Press release). California Air Resources Board. June 28, 2001. Retrieved 2 September 2021.
  11. ↑ "GM Pulls the Plug on Inductive Charging: Letter from General Motors Advanced Technology Vehicles.". 2002-03-15. http://ev1-club.power.net/archive/020315/index.htm. 
  12. ↑ "Plug-In Vehicle Tracker: What's Coming, When". November 23, 2009. http://www.pluginamerica.org/vehicles. 
  13. ↑ "j1772 Connector Conversion for Avcon Cables". Beata Electric Motor Carriage Collection. http://www.tzev.com/j1772_avcon_head_connector_conversion.html. 

External links



Retrieved from "https://handwiki.org/wiki/index.php?title=Company:Avcon&oldid=3713873"