Engineering:Class-D amplifier

From HandWiki
Short description: Audio amplifier based on switching


Block diagram of a basic class-D amplifier.
Note: For clarity, signal periods are not shown to scale.

A class-D amplifier or switching amplifier is an electronic amplifier in which the amplifying devices (transistors, usually MOSFETs) operate as electronic switches, and not as linear gain devices as in other amplifiers. They operate by rapidly switching back and forth between the supply rails, using pulse-width modulation, pulse-density modulation, or related techniques to produce a pulse train output. A simple low-pass filter may be used to attenuate their high-frequency content to provide analog output current and voltage. Little energy is dissipated in the amplifying transistors because they are always either fully on or fully off, so efficiency can exceed 90%.

History

The first Class-D amplifier was invented by British scientist Alec Reeves in the 1950s and was first called by that name in 1955. The first commercial product was a kit module called the X-10 released by Sinclair Radionics in 1964. However, it had an output power of only 2.5 watts. The Sinclair X-20 in 1966 produced 20 watts but suffered from the inconsistencies and limitations of the germanium-based bipolar junction transistors available at the time. As a result, these early class-D amplifiers were impractical and unsuccessful. Practical class-D amplifiers were enabled by the development of silicon-based MOSFET (metal–oxide–semiconductor field-effect transistor) technology. In 1978, Sony introduced the TA-N88, the first class-D unit to employ power MOSFETs and a switched-mode power supply. There were subsequently rapid developments in MOSFET technology between 1979 and 1985. The availability of low-cost, fast-switching MOSFETs led to Class-D amplifiers becoming successful in the mid-1980s.[1] The first class-D amplifier based integrated circuit was released by Tripath in 1996, and it saw widespread use.[2]

Basic operation

Class-D amplifiers work by generating a train of rectangular pulses of fixed amplitude but varying width and separation. This modulation represents the amplitude variations of the analog audio input signal. In some implementations, the pulses are synchronized with an incoming digital audio signal removing the necessity to convert the signal to analog. The output of the modulator is then used to turn the output transistors on and off alternately. Since the transistors are either fully on or fully off, they dissipate very little power. A simple low-pass filter consisting of an inductor and a capacitor provides a path for the low frequencies of the audio signal, leaving the high-frequency pulses behind.

The structure of a class-D power stage is comparable to that of a synchronously rectified buck converter, a type of non-isolated switched-mode power supply (SMPS). Whereas buck converters usually function as voltage regulators, delivering a constant DC voltage into a variable load, and can only source current, a class-D amplifier delivers a constantly changing voltage into a fixed load. A switching amplifier may use any type of power supply (e.g., a car battery or an internal SMPS), but the defining characteristic is that the amplification process itself operates by switching.

The theoretical power efficiency of class-D amplifiers is 100%. That is to say, all of the power supplied to it is delivered to the load and none is turned to heat. This is because an ideal switch in its on state would encounter no resistance and conduct all the current with no voltage drop across it, hence no power would be dissipated as heat. And when it is off, it would have the full supply voltage across it but no leakage current flowing through it, and again no power would be dissipated. Real-world power MOSFETs are not ideal switches, but practical efficiencies well over 90% are common for class-D amplifiers. By contrast, linear AB-class amplifiers are always operated with both current flowing through and voltage standing across the power devices. An ideal class-B amplifier has a theoretical maximum efficiency of 78%. Class A amplifiers (purely linear, with the devices always at least partially on) have a theoretical maximum efficiency of 50% and some designs have efficiencies below 20%.

Signal modulation

The 2-level waveform is derived using pulse-width modulation (PWM), pulse-density modulation (sometimes referred to as pulse frequency modulation), sliding mode control (more commonly called self-oscillating modulation.[3]) or discrete-time forms of modulation such as delta-sigma modulation.[4]

A simple means of creating the PWM signal is to use a high-speed comparator ("C" in the block diagram above) that compares a high-frequency triangular wave with the audio input. This generates a series of pulses of which the duty cycle is directly proportional with the instantaneous value of the audio signal. The comparator then drives a MOS gate driver which in turn drives a pair of high-power switching transistors (usually MOSFETs). This produces an amplified replica of the comparator's PWM signal. The output filter removes the high-frequency switching components of the PWM signal and reconstructs audio information that the speaker can use.

DSP-based amplifiers that generate a PWM signal directly from a digital audio signal (e. g. SPDIF) either use a counter to time the pulse length[5] or implement a digital equivalent of the triangle-based modulator. In either case, the time resolution afforded by practical clock frequencies is only a few hundredths of a switching period, which is not enough to ensure low noise. In effect, the pulse length gets quantized, resulting in quantization distortion. In both cases, negative feedback is applied inside the digital domain, forming a noise shaper which results in lower noise in the audible frequency range.

Design challenges

Switching speed

Two significant design challenges for MOSFET driver circuits in class-D amplifiers are keeping dead times and linear mode operation as short as possible. Dead time is the period during a switching transition when both output MOSFETs are driven into cut-off mode and both are off. Dead times need to be as short as possible to maintain an accurate low-distortion output signal, but dead times that are too short cause the MOSFET that is switching on to start conducting before the MOSFET that is switching off has stopped conducting and the MOSFETs effectively short the output power supply through themselves in a condition known as shoot-through.

The controlling circuitry also needs to switch the MOSFETs as quickly as possible to minimize the amount of time a MOSFET is in linear mode—the state between cut-off mode and saturation mode where the MOSFET is neither fully on nor fully off and conducts current with significant resistance, creating significant heat. Failures that allow shoot-through or too much linear mode operation result in excessive losses and sometimes catastrophic failure of the MOSFETs.[6]

With fixed-frequency PWM modulation, as the (peak) output voltage approaches either of the supply rails, the pulse width can get so narrow as to challenge the ability of the driver circuit and the MOSFET to respond. These pulses can be as short as a few nanoseconds and can result in shoot through and heating due to linear mode operation. Other modulation techniques such as pulse-density modulation can achieve higher peak output voltages, as well as greater efficiency compared to fixed-frequency PWM.

Electromagnetic interference

The switching power stage generates both high dV/dt and dI/dt, which give rise to radiated emission whenever any part of the circuit is large enough to act as an antenna. In practice, this means the connecting wires and cables will be the most efficient radiators so most effort should go into preventing high-frequency signals reaching those:

  • Avoid capacitive coupling from switching signals into the wiring.
  • Avoid inductive coupling from various current loops in the power stage into the wiring.
  • Use one unbroken ground plane and group all connectors together, in order to have a common RF reference for decoupling capacitors
  • Include the equivalent series inductance of filter capacitors and the parasitic capacitance of filter inductors in the circuit model before selecting components.
  • Wherever ringing is encountered, locate the inductive and capacitive parts of the resonant circuit that causes it, and use parallel RC or series RL snubbers to reduce the Q of the resonance.
  • Do not make the MOSFETs switch any faster than needed to fulfil efficiency or distortion requirements. Distortion is more easily reduced using negative feedback than by speeding up switching.

Power supply design

Class-D amplifiers place an additional requirement on their power supply, namely that it be able to sink energy returning from the load. Reactive (capacitive or inductive) loads store energy during part of a cycle and release some of this energy back later. Linear amplifiers will dissipate this energy, class-D amplifiers return it to the power supply which should somehow be able to store it. In addition, half-bridge class D amplifiers transfer energy from one supply rail (e.g. the positive rail) to the other (e.g. the negative) depending on the sign of the output current. This happens regardless of whether the load is resistive or not. The supply should either have enough capacitive storage on both rails, or be able to transfer this energy back.[7]

Active device selection

The active devices in a Class D amplifier need only act as controlled switches, and need not have particularly linear response to the control input. Bipolar transistors or field-effect transistors are usually used. Vacuum tubes can be used as power switching devices in Class-D power audio amplifiers.[8]

Error control

The actual output of the amplifier is not just dependent on the content of the modulated PWM signal. The power supply voltage directly amplitude-modulates the output voltage, dead time errors make the output impedance non-linear and the output filter has a strongly load-dependent frequency response. An effective way to combat errors, regardless of their source, is negative feedback. A feedback loop including the output stage can be made using a simple integrator. To include the output filter, a PID controller is used, sometimes with additional integrating terms. The need to feed the actual output signal back into the modulator makes the direct generation of PWM from a SPDIF source unattractive.[9] Mitigating the same issues in an amplifier without feedback requires addressing each separately at the source. Power supply modulation can be partially canceled by measuring the supply voltage to adjust signal gain before calculating the PWM[10] and distortion can be reduced by switching faster. The output impedance cannot be controlled other than through feedback.

Advantages

The major advantage of a class-D amplifier is that it can be more efficient than a linear amplifier, with less power dissipated as heat in the active devices. Given that large heat sinks are not required, Class-D amplifiers are much lighter weight than class A, B, or AB amplifiers, an important consideration with portable sound reinforcement system equipment and bass amplifiers. Output stages such as those used in pulse generators are examples of class-D amplifiers. However, the term mostly applies to power amplifiers intended to reproduce audio signals with a bandwidth well below the switching frequency.

Boss Audio mono amp. The output stage is top left, the output chokes are the two yellow toroids underneath.

Uses

  • Home theater in a box systems. These economical home cinema systems are almost universally equipped with class-D amplifiers. On account of modest performance requirements and straightforward design, direct conversion from digital audio to PWM without feedback is most common.
  • Mobile phones. The internal loudspeaker is driven by up to 1 W. Class D is used to preserve battery lifetime.
  • Hearing aids. The miniature loudspeaker (known as the receiver) is directly driven by a class-D amplifier to maximize battery life and can provide saturation levels of 130 dB SPL or more.
  • Powered speakers
  • High-end audio is generally conservative with regards to adopting new technologies but class-D amplifiers have made an appearance[11]
  • Active subwoofers
  • Sound reinforcement systems. For very high power amplification the power loss of AB amplifiers is unacceptable. Amplifiers with several kilowatts of output power are available as class-D. Class-D power amplifiers are available that are rated at 3000 W total output, yet weigh only 3.6 kg (8 lb).[12]
  • Bass instrument amplification
  • Radio frequency amplifiers may use Class D or other switch-mode classes to provide high efficiency RF power amplification in communications systems.[13]

See also

References

  1. Duncan, Ben (1996). High Performance Audio Power Amplifiers. Newnes. pp. 147–148. ISBN 9780750626293. 
  2. "Class-D Audio: The Power and the Glory". 30 December 2010. https://spectrum.ieee.org/geek-life/tools-toys/classd-audio-the-power-and-the-glory. 
  3. The generic analysis of sliding mode control is quite math heavy. The specific case of 2-state self-oscillating class-D amplifiers is much more intuitive and can be found in Globally Modulated Self-Oscillating Amplifier with Improved Linearity, 37th AES Conference
  4. The Analog Devices AD1990 class-D audio power amplifier is an example.
  5. Sandler et al., Ultra-Low Distortion Digital Power Amplification, Presented at the 91st AES convention
  6. Analytical and numerical analysis of dead-time distortion in power inverters
  7. "IRAUDAMP7S, 25W-500W Scalable Output Power Class D Audio Power Amplifier Reference Design, Using the IRS2092S Protected Digital Audio Driver". October 28, 2009. p. 26. https://www.irf.com/technical-info/refdesigns/iraudamp7s.pdf. 
  8. Rampin M., 2015. AmpDiVa White Paper - On the use of vacuum tubes as switching devices in Class-D power audio amplifiers
  9. Putzeys et al. All Amplifiers etc., Presented at the AES 120th convention
  10. Boudreaux, Randy, Real-Time Power Supply Feedback Reduces Power Conversion Requirements For Digital Class D Amplifiers
  11. "Group review of "high end" class D offerings and round-table discussion with amplifier designers". http://www.enjoythemusic.com/tas/166/. 
  12. "Behringer | Product | NX3000D". https://www.behringer.com/product.html?modelCode=P0CHW. 
  13. Andrei Grebennikov, Nathan O. Sokal, Marc J Franco, Switchmode RF Power Amplifiers, Newnes, 2011, ISBN:0080550649, page vii

External links