Engineering:Cone calorimeter
 | This article may be written from a fan's point of view, rather than a neutral point of view. (May 2014) (Learn how and when to remove this template message) |
A cone calorimeter is an instrument used to study the behavior of fire in small samples of condensed phase materials. It is widely used in the field of fire safety engineering and in oxygen consumption calorimetry.[1]
The instrument gathers data about the ignition time, mass loss, combustion products, heat release rate, and other parameters associated with the sample's burning properties. The measurement of the heat release rate is based on Huggett's principle[2] that the gross heat of combustion of any organic material is directly related to the amount of oxygen required for combustion. Its name comes from the conical shape of a radiant heater incorporated into the instrument that can produce a nearly uniform heat flux over the surface of the sample under study.[3]
Development
In the 1960s, researchers at the National Institute of Standards and Technology (NIST) determined that the heat release from a fire directly related to the growth rate of a fire and was thus a major factor in the fire's risk to life and property. However, prior devices used to measure heat release typically estimated the heat release of a fire by measuring the increase in temperature of ambient air flowing past the combusting material and these measurements of heat release were often inaccurate, so a more reliable device was desired.[4]
Through the 1960s and 1970s, research efforts developed a more accurate method for estimating heat release. In 1977, William Parker published research that demonstrated that heat release during combustion was roughly constant per unit of oxygen consumed for a variety of fuels. By measuring the oxygen consumed during combustion, one could estimate heat release of a fire; this method is now termed oxygen consumption calorimetry.[5] This finding was a rediscovery of a method first identified in 1917 by W. M. Thornston, whose research similarly found that during combustion of organic liquids and gases, a consistent amount of heat was released per unit mass of oxygen consumed.[6] Clayton Huggett later provided a rigorous proof of concept in his 1980 paper to suggest oxygen consumption calorimetry was a significantly more accurate method for estimating heat release than prior methods.[2]
Following the development of oxygen consumption calorimetry, in 1982, Vytenis Babrauskas and colleagues at the Center for Fire Research built the first cone calorimeter.[7] The cone calorimeter was quickly realized as an important instrument for modern fire safety tests, being formally recognized in 1988 by an R&D 100 Award.[8] The cone calorimeter is used today for both regulatory and research purposes.[3]
Use
The cone calorimeter is used in several standard models to evaluate different aspects of flammable materials. As a reduced-scale apparatus, the size of the instrument typically limits the size of samples to less than 100 mm2.[1] Compared to previous devices used in calorimetry, the cone calorimeter produces more reliable data, but must be scaled up to reflect actual fire safety considerations.[4]
The instrument is used by encasing a small sample in aluminium foil, wool, and a retainer frame that is ignited below an exhaust hood. A conical heater is placed in between in order for materials to combust. The cone-shaped Inconel heating element provides a controllable radiant flux onto the sample, turning electricity into heat not unlike an electric toaster or oven. The flammability of a sample can be characterized as a function of heat flux onto a sample. The conical heater is open in its center, allowing products of combustion to flow upwards into an exhaust duct. Soot can be collected in the bottom of the frame for gravimetric analysis.
Ventilation is also a very important part of the device, as well as the electrical power to run the conical heater. A small water supply is necessary to cool and regulate the heat in the system of the device. Since temperature and pressure are being evaluated, two different measurement tools are needed in the exhaust tube. Gas samples, smoke measurements, and soot collections are also acquired using this device.
See also
- Flammability
- Flammability diagram
- Fire test
- Fire-safe polymers
- Fire protection engineering
References
- ↑ 1.0 1.1 Twilley, William H. (1988). "User's Guide for the Cone Calorimeter" (in en). NASA Sti/Recon Technical Report N 89: 22086. Bibcode: 1988STIN...8922086T. https://books.google.com/books?id=CX5_QgAACAAJ&q=Cone+calorimeter.
- ↑ 2.0 2.1 Hugget, C (1980). "Estimation of rate of heat release by means of oxygen consumption measurements". Fire and Materials 4 (2): 61–65. doi:10.1002/fam.810040202.
- ↑ 3.0 3.1 Beyler, Craig (14 January 2017). "Oxygen consumption calorimetry, William Parker: 2016 DiNenno Prize". Fire Science Reviews 61 (1). doi:10.1186/s40038-016-0016-z.
Material was copied from this source, which is available under a Creative Commons Attribution 4.0 International License.
- ↑ 4.0 4.1 Lide, David R (2001). A century of excellence in measurements, standards, and technology 1901-2000 (Report). Gaithersburg, MD: National Institute of Standards and Technology. pp. 280-282. http://dx.doi.org/10.6028/nist.sp.958.
- ↑ Parker, W J (1977). An investigation of the fire environment in the ASTM E 84 tunnel test (Report). Gaithersburg, MD: National Bureau of Standards. http://dx.doi.org/10.6028/nbs.tn.945.
- ↑ Thornton, W. M. (1917). "The relation of oxygen to the heat of combustion of organic compounds". The London, Edinburgh, and Dublin Philosophical Magazine and Journal of Science 33 (194): 196-203. doi:10.1080/14786440208635627. https://www.tandfonline.com/doi/abs/10.1080/14786440208635627.
- ↑ Babrauskas, Vytenis; Lawson, J Randall; Walton, W D; Twilley, William H (1982). Upholstered furniture heat release rates measured with a furniture calorimeter (Report). Gaithersburg, MD: National Bureau of Standards. http://dx.doi.org/10.6028/nbs.ir.82-2604.
- ↑ "Happy Retirement, Cone Calorimeter!" (in en). NIST. 2022-03-31. https://www.nist.gov/news-events/news/2022/03/happy-retirement-cone-calorimeter.
External links
- U.S. National Bureau of Standards "NBS Special Publication 745: User Guide for Cone Calorimeter" 1988
- Cone Calorimeter by Fire Testing Technology Ltd
- Diagram of a cone calorimeter
- Color diagram of a cone calorimeter
- Ten Years of Heat Release Research with the Cone Calorimeter by Dr. Vyto Babrauska of Fire Science and Technology, Inc
- "Cone calorimeter analysis of UL-94 V-rated plastics" Fire Mater. 2007; 31:257–283
 |  |
