Physics:ASTM G65

From HandWiki
ASTM G65

ASTM G65 is an international ASTM test method standard for measuring abrasion resistance of metallic materials and their surface treatments using a dry sand/rubber wheel apparatus. First published in 1980 and most recently revised in 2021, it has become a predominant test method for evaluating wear resistance in industries including mining, petroleum, construction, and agriculture.

History

The test method was developed to provide a reproducible laboratory procedure for ranking the abrasion resistance of materials subjected to low- to moderate-stress three-body abrasion, such as that produced by silica sand entrained between sliding surfaces.

It evolved from early work on sand-rubber-wheel testing by C. W. Haworth (1949) and was refined through round-robin evaluations organized by ASTM Committee G02 on Wear and Erosion during the 1970s, culminating in the first issue of ASTM G65, “Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus.” Since then many revisions have occurred but the bulk of the testing process remains the same.

Test principle

Apparatus

The test employs a rubber wheel of specified hardness (Durometer A-60) and diameter (228.6 mm) that rotates against a flat test specimen while a controlled flow of dry sand is fed between them.[1] The sand abrasive needed is a very specific rounded quartz grains (AFS 50/70 test sand) with a size distribution between 212 and 300 micrometers.[2]

Test procedures

ASTM G65 defines five standard procedures (A through E) with varying parameters:[1]

Procedure Force (N) Revolutions Duration Typical use
A 130 6,000 30 min Ranking materials
B 130 2,000 10 min Thin coatings (<0.5 mm)
C 130 100 Variable Research studies
D 45 6,000 30 min Thin/soft coatings
E 130 1,000 5 min Material ranking

Measurement and reporting

The primary measurement is volume loss in cubic millimeters (mm³), calculated from mass loss and material density.[3] Results may also be reported as:

  • Mass loss (mg)
  • Wear rate (mm³/m of sliding distance)
  • Relative wear resistance compared to a reference material

Factors affecting results

Multiple variables can influence test outcomes:

Material factors

Test variables

  • Sand flow rate (300-400 g/min specified)[5]
  • Wheel condition and replacement interval
  • Environmental humidity and temperature[6]
  • Specimen preparation and mounting

Applications

The test is widely employed for:

  • Materials selection for equipment exposed to abrasive conditions
  • Quality control of hardfacing and surface treatments
  • Development of wear-resistant alloys and coatings
  • Forensic analysis of wear failures

Industries utilizing G65 testing include:

  • Mining and mineral processing (crusher components, slurry pumps)
  • Agriculture (tillage tools, harvesting equipment)
  • Oil and gas (drill pipe, valve components)
  • Construction (excavator teeth, concrete handling)

Limitations

ASTM G65 has several recognized limitations:

  • Does not simulate all wear mechanisms (excludes impact wear, erosion corrosion)[5]
  • Limited to relatively low contact stresses
  • May not correlate with field performance in wet or corrosive environments
  • Ranking may differ from high-stress abrasion conditions like (ASTM G81)
  • ASTM G75 - Test Method for Determination of Slurry Abrasivity (Miller Number)
  • ASTM G76 - Test Method for Conducting Erosion Tests by Solid Particle Impingement
  • ASTM G105 - Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
  • ASTM B611 - Test Method for Determining the High Stress Abrasion Resistance
  • DIN 50332 - German equivalent standard
  • ISO 28080 - International standard for rubber wheel abrasion

See also

References

  1. ↑ 1.0 1.1 "Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus". ASTM International. https://www.astm.org/g0065-16r21.html. Retrieved 2024-11-11. 
  2. ↑ Hawk, J.A.; Wilson, R.D. (2001). "Tribology of Earthmoving, Mining, and Minerals Processing". Modern Tribology Handbook (CRC Press) 2: 1331–1370. 
  3. ↑ Budinski, K.G.; Budinski, M.K. (2018). Engineering Materials: Properties and Selection (10th ed.). Pearson. pp. 156–159. ISBN 978-0134319650. 
  4. ↑ Zum Gahr, K.H. (1987). "Microstructure and Wear of Materials". Tribology Series (Elsevier) 10. ISBN 0-444-42754-6. 
  5. ↑ 5.0 5.1 Gates, J.D. (1998). "Two-body and three-body abrasion: A critical discussion". Wear 214 (1): 139–146. doi:10.1016/S0043-1648(97)00188-9. 
  6. ↑ "ASTM G65 Dry Sand Abrasion Testing Technical Reference". US Corrosion Services. 30 April 2023. https://uscorrosion.com/index.php/dry-sand-abrasion-testing-by-our-houston-lab/. Retrieved 2024-11-11. 



Retrieved from "https://handwiki.org/wiki/index.php?title=Physics:ASTM_G65&oldid=4202375"