Engineering:Cofferdam
A cofferdam is an enclosure built within a body of water to allow the enclosed area to be pumped out or drained.[1] This pumping creates a dry working environment so that the work can be carried out safely. Cofferdams are commonly used for construction or repair of permanent dams, oil platforms, bridge piers, etc., built within water.
These cofferdams are usually welded steel structures, with components consisting of sheet piles, wales, and cross braces. Such structures are usually dismantled after the construction work is completed.[2]
The origin of the word comes from coffer (originally from Latin cophinus meaning 'basket')[3] and dam from Proto-Germanic *dammaz meaning 'barrier across a stream of water to obstruct its flow and raise its level').[4]
Uses
For dam construction, two cofferdams are usually built, one upstream and one downstream of the proposed dam, after an alternative diversion tunnel or channel has been provided for the river flow to bypass the foundation area of the dam. These cofferdams are typically a conventional embankment dam of both earth- and rock-fill, but concrete or some sheet piling also may be used. Usually, upon completion of the dam and associated structures, the downstream coffer is removed and the upstream coffer is flooded as the diversion is closed and the reservoir begins to fill. Depending on the geography of a dam site, in some applications, a U-shaped cofferdam is used in the construction of one half of a dam. When complete, the cofferdam is removed and a similar one is created on the opposite side of the river for the construction of the dam's other half.
Cofferdams are used in ship husbandry to allow dry access to underwater equipment and to close underwater openings while work is done on the fittings inside the ship. This is more common in naval vessels where a cofferdam may fit several vessels of a class.[5]
The cofferdam is also used on occasion in the shipbuilding and ship repair industry, when it is not practical to put a ship in drydock for repair work or modernization. An example of such an application is the lengthening of ships. In some cases a ship is actually cut in two while still in the water, and a new section of ship is floated in to lengthen the ship. The cutting of the hull is done inside a cofferdam attached directly to the hull of the ship; the cofferdam is then detached before the hull sections are floated apart. The cofferdam is later replaced while the hull sections are welded together again. As expensive as this may be to accomplish, the use of a drydock might be even more expensive.
Cofferdams are also used in some marine salvage operations.[6]:Ch.10
Examples
A 100-ton open caisson that was lowered more than a mile to the sea floor in attempts to stop the flow of oil in the Deepwater Horizon oil spill has been called a cofferdam.[citation needed]
A cofferdam over 1 mile long was built to permit the construction of the Livingstone Channel in the Detroit River.[7] See main article at Stony Island.
Types
Several types of structure performing this function can be distinguished, depending on how they are constructed and how they are used.[5]
Civil and coastal engineering
A cofferdam is a space between two watertight bulkheads or decks within a ship. It is usually a void (empty) space intended to ensure that the contents of nearly adjacent tanks cannot leak directly from one to the other which would result in contamination of the contents of one or both of the compartments.[8] The cofferdam would be kept empty at all times and the ship may have sensors within it to warn if it has begun to fill with liquid. If two different cargoes that react dangerously with each other are carried on the same vessel, one or more cofferdams are usually required between the cargo spaces.[citation needed]
Marine salvage
When all or part of the main deck of a sunken ship is submerged, flooded spaces cannot be dewatered until all openings are sealed or the effective freeboard is extended above the high water level. One method of doing this is to build a temporary watertight extension of the entire hull of the ship, or the space to be dewatered, to the surface. This watertight extension is a cofferdam. Although they are temporary structures, cofferdams for this purpose have to be strongly built, adequately stiffened, and reinforced to withstand the hydrostatic and other loads that they will have to withstand. Large cofferdams are normally restricted to harbor operations.[6]:Ch.10
Complete cofferdams cover most or all of the sunken vessel and are equivalent to extensions of the ship's sides to above the water surface.[6]:Ch.10
Partial cofferdams are constructed around moderate-sized openings or areas such as a cargo hatch or small deckhouse. They can often be prefabricated and installed as a unit, or prefabricated panels can be joined during erection. When partial cofferdams are used, it may be necessary to compensate for hydrostatic pressure on the deck by shoring the decks. With both complete and partial cofferdams, there is usually a large free surface in the spaces being pumped. Sometimes this can be limited by dewatering one compartment at a time, or in groups, taking into account the beam strength loads on the ship induced by the load distribution.[6]:Ch.10
Small cofferdams are used for pumping or to allow salvors access to spaces that are covered by water at some stage of the tide. They are usually prefabricated and fitted around minor openings.[6]:Ch.10
Diving work on cofferdams often involves clearing obstructions, fitting, and fastening, including underwater welding, and where necessary, caulking, bracing and shoring the adjacent structure.[6]:Ch.10
Ship husbandry
There are two common types of dry chambers used in underwater ship husbandry. Open bottom cofferdams allow divers direct access to the enclosed hull area, system, or opening. The flange sides of the chamber secure and seal against the hull, acting as an airtight boundary. Open bottom cofferdams are typically used as diver work space for rigging or welding and ventilation for welding or epoxy cure, where there is no opening to the interior of the vessel, or the interior is pressurised in this area. The air space is at the pressure of the water surface at the bottom of the chamber. Open top cofferdams allow surface access to the work area below the waterline, and are at atmospheric pressure. Openings through the hull to the interior of the ship are possible.[5]
Portable cofferdams
Portable cofferdams can be inflatable or frame and fabric cofferdams that can be reused. Inflatable cofferdams are stretched across the site, then inflated with water from the prospected dry area. Frame and fabric cofferdams are erected in the water and covered with watertight fabric. Once the area is dry, water still remaining from the dry area can be siphoned over to the wet area.[clarification needed][citation needed]
See also
- Caisson, a similar watertight structure
- Dental dam
References
- ↑ Chisholm, Hugh, ed (1911). "Cofferdam". Encyclopædia Britannica. 6 (11th ed.). Cambridge University Press. p. 649.
- ↑ "Cofferdam, Cofferdam Design, Cofferdam Applications – Dam-it Dams" (in en-US). http://www.damitdams.com/cofferdam/.
- ↑ Harper, Douglas. "coffer". Douglas Harper. https://www.etymonline.com/search?q=coffer&ref=searchbar_searchhint.
- ↑ Harper, Douglas. "dam". Douglas Harper. https://www.etymonline.com/word/dam?ref=etymonline_crossreference#etymonline_v_747.
- ↑ 5.0 5.1 5.2 "16. Cofferdams". Underwater Ship Husbandry Manuals (Revision 0, Change H ed.). 15 November 2011. S0600-AA-PRO-160. https://www.navsea.navy.mil/Portals/103/Documents/SUPSALV/UWSH/chap16.pdf.
This article incorporates text from this source, which is in the public domain.
- ↑ 6.0 6.1 6.2 6.3 6.4 6.5 U.S. Navy Salvage Manual. 1: Strandings, Harbor Clearance and Afloat Salvage S0300-A6-MAN-010. United States. Navy Department. Supervisor of Salvage and Diving.. 31 May 2013. https://www.navsea.navy.mil/Portals/103/Documents/SUPSALV/Salvage%20Docs/Salvage%20Manual%20Vol%201%20S0300-A6-MAN-010.pdf. Retrieved 28 March 2023.
- ↑ "Detroit Free Press from Detroit, Michigan on March 27, 1910 · Page 65" (in en). 27 March 1910. http://www.newspapers.com/newspage/118664822/.
- ↑ Palmer, Joseph (1975). Jane's Dictionary of Naval Terms. London: Macdonald and Janes. ISBN 0-356-08258-X.
External links
 |  |
