Engineering:Crossbow bolt

From HandWiki
Short description: Dart-like projectile used by crossbows
An unusually small crossbow bolt with a tapered "waist" shaft section and rear skirt compared to a 1 euro cent coin

A bolt or quarrel is a dart-like projectile used by crossbows.[1] The word quarrel is from the Old French quarrel (> French carreau) "square thing",[2] specialized use as quarrel d'arcbaleste (> carreau d'arbalète) "crossbow quarrel", referring to their typically square heads. Although their lengths vary, bolts are typically shorter and heavier than traditional arrows shot with longbows.[3]

Parts of the bolt

Point

Main page: Engineering:Arrowhead

The point, also called the head or the tip, is the pointed and weighted front end of the bolt, which is sharp and hard so that it can penetrate the target.

Shaft

The shaft is the main body of the bolt to which other parts of the bolt are attached. In modern times it is normally made of carbon fibre or aluminium alloy (or sometimes both aluminum and carbon fibre are used), and is very lightweight for its strength. Shafts come with varying degrees of stiffness — referred to as the "spine" of the bolt. The more resistant to bending a bolt is, the more "spine" it is said to have, and a crossbow with higher draw weight ideally needs to be paired with a heavier bolt point and higher spine specifications. The weight of a shaft is usually in grains, and product descriptions may provide the total weight in grains, or in grains per inch (GPI), for which the total weight of shaft can be calculated by multiplying the GPI value with length of shaft in inches.

Fletching

Main page: Engineering:Fletching

Fletchings, also referred to as vanes, are fins located at the rear end of the shaft just before the nock. The fletching is typically made from soft light materials such as feathers, plastic or silicone rubber. They stabilize the trajectory of the bolt via three different means: resisting pitching and yawing of the shaft by acting like a stabilizer fin (fin-stabilization); reducing deviation from the longitudinal axis by creating a back-pulling center of pressure behind the bolt's center of mass (drag-stabilization); and in some particular cases, creating a rotation around the longitudinal axis (spin-stabilization) by having the fletchings mounted at a slight angle of attack.

There is no rule or formula for determining the length of fletching needed — generally the longer the shaft is, the longer the fletching needs to be, and vice versa.

Nock

A nock is a small notched piece that is attached to the rear end of the shaft, for engaging and receiving the propulsive push from the string during shooting. Nocks are made of either plastic or aluminum.

Size and weight

There is not any hard and fast rule of bolt sizing. Generally, the bolts are 15 to 22 inches long but the standard length is 20 inches. Experts recommend longer bolts[4] but they have certain disadvantages as well.

The weight of the bolt can have a serious effect on the range of the bolt. The bolt's total weight includes the bolt's weight, nock, insert, vanes, and broadhead or field point. Almost all bolt manufacturers will list how many grains each shaft weighs or how many grains are in each inch of the shaft. A more massive bolt, e.g. at least 400 grains, will have better downrange energy and offer better penetration but will travel more slowly and thus drop more due to gravity during its flight. A lighter bolt will fly quicker and give the shooter a longer range, but might not have the desired penetration.

References

  1. "Quarrel". http://www.merriam-webster.com/dictionary/quarrel. 
  2. T. F. Hoad, English Etymology, Oxford University Press, 1993 (ISBN:0-19-283098-8). p. 382a
  3. Stone, George Cameron (1999). A Glossary of the Construction, Decoration, and Use of Arms and Armor in All Countries and in All Times. Mineola NY: Dover Publications. pp. 125. ISBN 0-486-40726-8. 
  4. "Can I use longer bolts? - Excalibur Crossbow Forum". https://www.excaliburcrossbow.com/phpBB3/viewtopic.php?t=68124.