Engineering:Heat-shrink tubing

From HandWiki
Short description: Shrinkable plastic tube used to insulate wires
Animation of heat-shrink tubing, before and after shrinking

Heat-shrink tubing (or, commonly, heat shrink or heatshrink) is a shrinkable plastic tube used to insulate wires, providing abrasion resistance and environmental protection for stranded and solid wire conductors, connections, joints and terminals in electrical wiring. It can also be used to repair the insulation on wires or to bundle them together, to protect wires or small parts from minor abrasion, and to create cable entry seals, offering environmental sealing protection. Heat-shrink tubing is ordinarily made of polyolefin, which shrinks radially (but not longitudinally) when heated, to between one-half and one-sixth of its diameter.

Heat-shrink tubing is manufactured in a multitude of varieties and chemical makeups with the exact composition of each type being dependent on the intended application.[1] From near microscopically-thin-wall tubing to rigid, heavy-wall tubing, each type has precise design and chemical additives that make it suitable for meeting any of a wide variety of environmental demands. Heat-shrink tubing is rated by its expansion ratio, a comparison of the differences in expansion and recovery rate.

Use

The unshrunk tubing is fitted on the wire before making the connection, then slid down to cover the joint after it is made. If the fit is tight, silicone lubricant can be applied without compromising the heat-shrink material.[2] The tubing is then shrunk to wrap tightly around the joint by heating in an oven or with a hot air gun or other source of hot gas flow. Convenient but less consistent methods for shrinking the tube include a soldering iron held close to but not touching the tube, or the heat from a lighter. Uncontrolled heat can cause uneven shrinkage, physical damage and insulation failure, and these methods are not recommended by heatshrink suppliers.[2] If overheated, heat-shrink tubing can melt, scorch or catch fire like any other plastic. Heating causes the tubing to contract to between half and one sixth of its original diameter, depending on the material used, providing a snug fit over irregularly shaped joints. There is also longitudinal shrinking, usually unwanted and to a lesser extent than narrowing, of typically around 6%.[2] The tubing provides good electrical insulation, protection from dust, solvents and other foreign materials, and mechanical strain relief, and is mechanically held in place (unless incorrectly oversized or not properly shrunk) by its tight fit. File:Video of Heat shrink tube before and after.ogv

Some types of heat-shrink contain a layer of thermoplastic adhesive on the inside to help provide a good seal and better adhesion, while others rely on friction between the closely conforming materials. Heating non-adhesive shrink tube to very near the melting point may allow it to fuse to the underlying material as well[citation needed].

Heatshrink tubing is sometimes sold in pre-cut lengths, with a solder blob at the center of the length, as this configuration was specified by Daimler-Benz for automotive electrical repairs.[3]

One application that has used heatshrink in large quantities since the early 1970s is the covering of fibreglass helical antennas, used extensively for 27 MHz CB radio. Many millions of these antennas have been coated this way.[citation needed]

Manufacture

Heat-shrink tubing was invented by Raychem Corporation[4] in 1962.[5] It is manufactured from a thermoplastic material such as polyolefin, fluoropolymer (such as FEP, PTFE or Kynar), PVC, neoprene, silicone elastomer or Viton.

The process for making heat-shrink tubing is as follows: First the material is chosen based on its properties. The material is often compounded with other additives (such as colorants, stabilizers, etc.) depending on the application. A starting tube is extruded from the raw material. Next, the tube is taken to a separate process where it is cross-linked, usually through radiation. The cross-linking creates a memory in the tube. Then the tube is heated to just above the polymer's crystalline melting point and expanded in diameter, often by placing it in a vacuum chamber. While in the expanded state it is rapidly cooled. Later, when heated (above the crystalline melting point of the material) by the end user, the tubing shrinks back to its original extruded size.

The material is often cross-linked through the use of electron beams,[6] peroxides, or moisture. This cross-linking creates the memory in the tubing so that it is able to shrink back to its original extruded dimensions upon heating, producing a material called heat-shrink tubing. For outdoor use, heat-shrink tubing often has a UV stabiliser added.

Materials

Different applications require different materials:

  • Elastomeric tubes maintain high flexibility even at low temperatures and meet stringent international specifications. Their operating temperature range is -75 to 150 °C. The material is resistant to many chemicals (including diesel and petrol) and has good resistance to abrasion, even in severe environmental conditions. A common shrink ratio is 2:1.[7]
  • Fluorinated ethylene propylene (FEP) is a lower-cost alternative to PTFE.[citation needed] It is a versatile electrical insulator and is inert to most chemicals and solvents. Additionally, it is highly resistant to extreme heat, cold, and ultraviolet radiation, making it an excellent material for heat-shrink tubing applications.
  • Polyolefin tubes, the most common kind,[8] have maximum continuous-use temperatures from -55 to 135 °C, and are used by the military, aerospace and railway industries. They are flexible and fast-shrinking, and manufactured in a wide range of colors (including clear), which can be used for color-coding wires. With the exception of black, they tend to have lower resistance to ultraviolet light; accordingly, only black is recommended for outdoor applications. Polyolefin tubing shrinks at 143 °C.[9] Polyolefin heat-shrink tubing typically shrinks 2:1 diametrically,[10][9] but high-grade polyolefin heat-shrink is also available with a 3:1 ratio.[7] Polyolefin tubing may withstand being touched with a soldering iron.[10]
  • PVC tubes are usually lower cost than other materials.[1] PVC takes colors exceptionally well and is available in nearly unlimited colors both opaque and transparent. PVC can be used outdoors with the addition of a UV stabilizer.[citation needed] PVC heat-shrink tends to burn if touched with a soldering iron.[10]
  • Polyvinylidene fluoride (PVDF) tubes are intended for high temperature applications.[citation needed]
  • Silicone rubber offers excellent resistance to scrape abrasion and high flexibility. Its operating temperature range is -50 to 200 °C[citation needed]
  • PTFE (fluoropolymer) tubes have a wide operating temperature range (-55 to 175 °C), a low coefficient of friction, and high resistance to chemicals and punctures.[7]
  • Viton, another fluoropolymer with high chemical resistance, is widely used in hydraulic equipment. It is highly flexible, with a very wide operating temperature range of -55 to 220 °C, making it suitable for protecting sensitive devices against heat.[7]

Other special materials exist, offering qualities such as resistance to diesel and aviation fuels, and there is also woven fabric, providing increased abrasion resistance in harsh environments.

Types

Heat-shrink tubing is available in a variety of colors for color-coding of wires and connections. In the early twenty-first century heat-shrink tubing started to be used for PC modding to tidy up the interior of computers and provide an appearance considered pleasing[citation needed]. In response to this opening market[citation needed], manufacturers started producing heat-shrink tubing in luminous and UV reactive varieties.

Although usually used for insulation, heat-shrink tubing with a conductive lining is also available, for use on joints which are not soldered.

Specialty heat-shrink tubing, known as "solder sleeves", have a tube of solder inside of the heat-shrink tubing, allowing the heat source to electrically join the two wires by melting the solder and simultaneously insulate the junction with the tubing. Solder sleeves also commonly contain a ring of heat-activated sealant on the inside of each end of the tubing, allowing the connection to also be made waterproof.[11]

Heat-shrink end caps, closed at one end, are used to insulate the exposed cut ends of insulated wires.

See also

Main standards and certificates

UL224-2010[12]

SAE AS23053[13]

ASTM D 2671[14]

ASTM D3150[15]

VW-1[16]

References

  1. ↑ 1.0 1.1 Heat Shrink Tubing Users Guide
  2. ↑ 2.0 2.1 2.2 cableorganizer.com: How to Use Heat Shrink Tubing
  3. ↑ Gilles, Tim (2015) (in English). Automotive Service. Cengage Learning. pp. 546. ISBN 9781305445932. https://books.google.com/books?id=Ji5-BAAAQBAJ&q=polyolefin+heat+shrink+temperature&pg=PA546. Retrieved 2016-11-20. 
  4. ↑ Quality Today. IPC Industrial Press. 1994. https://books.google.com/books?id=9U1WAAAAMAAJ. 
  5. ↑ U.S. Patent 3,396,460. U.S. Patent Office. 1968. http://www.freepatentsonline.com/3396460.pdf. 
  6. ↑ Accelerator apps: heat-shrink tubing , Symmetry, Dimensions of Particle Physics. V. 7, Issue 2, Apr. 10
  7. ↑ 7.0 7.1 7.2 7.3 "3M Heat Shrink catalogue". 3M. http://solutions.3m.com/wps/portal/3M/en_US/EMDCI/Home/Products/HeatShrinkProducts/. Retrieved 30 October 2014. 
  8. ↑ Kucklick, Theodore R. (2012). The Medical Device R&D Handbook, Second Edition. CRC Press. p. 19. ISBN 9781439811894. https://books.google.com/books?id=_zDx7xAM6ccC&q=polyolefin&pg=PA19. 
  9. ↑ 9.0 9.1 Wang, Xuefeng; Shaikh, Kashan A. (2009). "Interfacing Microfluidic Devices with the Macro World". in Wei-Cheng Tian, Erin Finehout (in English). Microfluidics for Biological Applications. Springer Science & Business Media. pp. 102. ISBN 9780387094809. https://books.google.com/books?id=8wyBp-vKbdcC&q=polyolefin. Retrieved 2016-11-20. 
  10. ↑ 10.0 10.1 10.2 Puckett, Larry (2015). Wiring Your Model Railroad. Kalmbach Publishing, Co.. p. 88. ISBN 9781627001762. https://books.google.com/books?id=65eZCgAAQBAJ&q=polyolefin&pg=PA88. 
  11. ↑ "Solder Sleeves: Solder, heat shrink and waterproof your splices in one operation". Inventables. https://www.inventables.com/technologies/solder-sleeves. Retrieved 2016-01-11. 
  12. ↑ "UL - 224 Extruded Insulating Tubing | Standards Catalog". https://standardscatalog.ul.com/standards/en/standard_224_6. 
  13. ↑ "AS23053: Insulation Sleeving, Electrical, Heat Shrinkable, General Specification For - SAE International". https://www.sae.org/standards/content/as23053/. 
  14. ↑ "ASTM D2671 - 13 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use". https://www.astm.org/Standards/D2671.htm. 
  15. ↑ "ASTM D3150 - 18 Standard Specification for Crosslinked and Noncrosslinked Poly(Vinyl Chloride) Heat-Shrinkable Tubing for Electrical Insulation". https://www.astm.org/Standards/D3150.htm. 
  16. ↑ "Everything there is to know about Heat Shrink Tubing". https://www.wkk-europe.com/news/post/everything-there-is-to-know-about-heat-shrink-tubing/. 

External links



Retrieved from "https://handwiki.org/wiki/index.php?title=Engineering:Heat-shrink_tubing&oldid=3236087"