Engineering:Metal fume fever

From HandWiki
Metal fume fever

Metal fume fever, also known as brass founders' ague, brass shakes,[1] zinc shakes, galvie flu, galvo poisoning, metal dust fever, welding shivers, or Monday morning fever,[2] is an illness primarily caused by exposure to chemicals such as zinc oxide (ZnO), aluminium oxide (Al2O3), or magnesium oxide (MgO) which are produced as byproducts in the fumes that result when certain metals are heated. Other common sources are fuming silver, gold, platinum,[3] and chromium.[4]

Welders are routinely exposed to fumes. The most common form of exposure among welders occurs when welding galvanized steel, of which zinc is the primary component of the galvanization process. Galvanized metal must be thoroughly cleaned using an angle grinder or other abrasive means to remove the galvanized coating before welding or burning. Brazing and soldering can also cause metal poisoning due to exposure to lead, zinc, copper, or cadmium.[5] In extreme cases, cadmium[6] (present in some older silver solder alloys) can cause loss of consciousness.

Signs and symptoms

The signs and symptoms are generally flu-like. They include fever, chills, nausea, headache, fatigue, muscle aches, joint pains, lack of appetite, shortness of breath, pneumonia, chest pain, change in blood pressure, dizziness, and coughing. A sweet or metallic taste in the mouth may also be reported, along with a dry or irritated throat which may lead to hoarseness.[7] Symptoms of a more severe metal toxicity may also include a burning sensation in the body, shock, no urine output, collapse, convulsions, shortness of breath, yellow eyes or yellow skin, rash, vomiting, watery or bloody diarrhea or low or high blood pressure, which require prompt medical attention.[8] For zinc oxide, the onset of symptoms may be delayed for several hours, but typically resolve within 24 to 48 hours.[9]

Cause

Exposure usually arises through hot metalworking processes, such as smelting and casting of zinc alloys, welding of galvanized metals, brazing, or soldering. If the metal concerned is particularly high-risk, the residue from cold sanding processes may also cause fume fever, even if the dose is lower. It may also be caused by electroplated surfaces or metal-rich anti-corrosion paint, such as cadmium passivated steel or zinc chromate primer on aluminium aircraft parts. Exposure has also been reported in use of lead-free ammunition, by the harder steel core stripping metal from the jacket of the bullet and barrel of the rifle.[10]

The most plausible metabolic source of the symptoms is a dose-dependent release of certain cytokines, an event which occurs by inhaling metal oxide fumes that injure the lung cells. This is not an allergic reaction, though allergic reactions to metal fumes can occur.[11]

Diagnosis

Diagnosis is primarily anecdotal, that is, it depends upon a good occupational history. Diagnosis of metal fume fever can be easily missed because the complaints are non-specific, resemble a number of other common illnesses, and presentation occurs typically 2–10 hours after the exposure.[12] When respiratory symptoms are prominent, metal fume fever may be confused with acute bronchitis or pneumonia. The diagnosis is based primarily upon a history of exposure to metal oxide fumes. Cain and Fletcher (2010) report a case of metal fume fever that was diagnosed only by taking a full occupational history and by close collaboration between primary and secondary health care personnel.[13]

Physical symptoms vary among persons exposed, depending largely upon the stage in the course of the syndrome during which examination occurs. Patients may present with wheezing or crackles in the lungs. They typically have an increased white blood cell count, and urine, blood plasma and skin zinc levels may be elevated. Chest X-ray abnormalities may also be present.[11]

An interesting feature of metal fume fever involves rapid adaptation to the development of the syndrome following repeated metal oxide exposure. Workers with a history of recurrent metal fume fever often develop a tolerance to the fumes. This tolerance, however, is transient, and only persists through the work week. After a weekend hiatus, the tolerance has usually disappeared. This phenomenon of tolerance is what led to the name "Monday Fever".[citation needed]

In 2018, there were 259 cases of metal fume fever reported to the United States Poison Control Center.[14]

Treatment

Treatment of mild metal fume fever consists of bedrest, keeping the patient well hydrated, and symptomatic therapy (e.g. aspirin for headaches) as indicated. In the case of non-allergic acute lung injury, standard or recommended approaches to treatment have not been defined.[11]

The consumption of large quantities of cow's milk, either before or immediately after exposure is a traditional remedy.[1] However, the United Kingdom Health and Safety Executive challenges this advice, warning, "Don't believe the stories about drinking milk before welding. It does not prevent you getting metal fume fever."[15]

Prevention

Prevention of metal fume fever in workers who are at risk (such as welders) involves avoidance of direct contact with potentially toxic fumes, improved engineering controls (exhaust ventilation systems), personal protective equipment (respirators), and education of workers regarding the features of the syndrome itself and proactive measures to prevent its development.[16]

In some cases, the product's design may be changed so as to eliminate the use of risky metals. Cadmium is often replaced by other metals. NiCd rechargeable batteries are being replaced by NiMH. These contain other toxic metals, such as chromium, vanadium and cerium. Zinc or nickel plating can be used instead of cadmium plating, and brazing filler alloys now rarely contain cadmium.[citation needed]

See also

References

  1. 1.0 1.1 Chastain, Steve (2004). Metal Casting: A Sand Casting Manual for the Small Foundry. Stephen Chastain. pp. 8. ISBN 0-9702203-2-4. https://books.google.com/books?id=BXqVDRHW-ocC&q=petrobond+bronze&pg=PA154. 
  2. Kaye, P; Young, H; O'Sullivan, I (2002). "Metal fume fever: A case report and review of the literature". Emergency Medicine Journal 19 (3): 268–9. doi:10.1136/emj.19.3.268. PMID 11971851. 
  3. El-Zein, M; Malo, J. L; Infante-Rivard, C; Gautrin, D (2003). "Prevalence and association of welding related systemic and respiratory symptoms in welders". Occupational and Environmental Medicine 60 (9): 655–61. doi:10.1136/oem.60.9.655. PMID 12937186. 
  4. "Chromium and you". Health and Safety Executive. 2013. http://www.hse.gov.uk/pubns/indg346.pdf. 
  5. "Welding, Cutting, Brazing | Environmental Health & Safety - The University of Alabama". http://ehs.ua.edu/operations/occupational-safety/shop-safety/welding-cutting-brazing/. 
  6. "Cadmium and you - working with Cadmium - are you at risk?". 2010. http://www.hse.gov.uk/pubns/indg391.pdf. 
  7. http://www.racgp.org.au/afp/201203/201203Wong.pdf[|permanent dead link|dead link}}][full citation needed]
  8. "Medline Medical Encyclopedia: Zinc"
  9. "Zinc oxide (UK PID)". https://inchem.org/documents/ukpids/ukpids/ukpid87.htm. 
  10. "Blyfri ammunisjon og helseplager - Forsvaret.no". http://forsvaret.no/aktuelt/publisert/nyheter/Sider/blyfri-ammo-helseplager.aspx. [full citation needed]
  11. 11.0 11.1 11.2 Kunimasa, Kei; Arita, Machiko; Tachibana, Hiromasa; Tsubouchi, Kazuya; Konishi, Satoshi; Korogi, Yohei; Nishiyama, Akihiro; Ishida, Tadashi (2011). "Chemical Pneumonitis and Acute Lung Injury Caused by Inhalation of Nickel Fumes". Internal Medicine 50 (18): 2035–8. doi:10.2169/internalmedicine.50.5557. PMID 21921392. 
  12. Greenberg, Michael I; Vearrier, David (2015). "Metal fume fever and polymer fume fever". Clinical Toxicology 53 (4): 195–203. doi:10.3109/15563650.2015.1013548. PMID 25706449. 
  13. Cain, J. R; Fletcher, R. M (2010). "Diagnosing metal fume fever--an integrated approach". Occupational Medicine 60 (5): 398–400. doi:10.1093/occmed/kqq036. PMID 20407044. 
  14. "2018 Annual Report of the American Association of Poison Control Centers' National Poison Data System (NPDS): 36th Annual Report". Clinical Toxicology 57 (12): 1220–1413. 2019-11-21. doi:10.1080/15563650.2019.1677022. PMID 31752545. https://piper.filecamp.com/uniq/meDKF2EpE2jsmTOs.pdf. Retrieved 2020-04-03. 
  15. "Illness caused by welding fume and gases". Health and Safety Executive (UK). http://www.hse.gov.uk/welding/illness.htm. 
  16. "Welding Fume Extraction" (in en-GB). https://www.1stopweldingshop.com/Catalogue/Safety-Fume-extraction/Fume-Extraction. 

External links

Classification