Standard temperature and pressure

From HandWiki
Short description: Reference values for temperature and pressure

Standard temperature and pressure (STP) are various standard sets of conditions for experimental measurements to be established to allow comparisons to be made between different sets of data. The most used standards are those of the International Union of Pure and Applied Chemistry (IUPAC) and the National Institute of Standards and Technology (NIST), although these are not universally accepted standards. Other organizations have established a variety of alternative definitions for their standard reference conditions.

In industry and commerce, the standard conditions for temperature and pressure are often necessary to define the standard reference conditions to express the volumes of gases and liquids and related quantities such as the rate of volumetric flow (the volumes of gases vary significantly with temperature and pressure): standard cubic meters per second (Sm3/s), and normal cubic meters per second (Nm3/s).

However, many technical publications (books, journals, advertisements for equipment and machinery) simply state "standard conditions" without specifying them; often substituting the term with older "normal conditions", or "NC". In special cases this can lead to confusion and errors. Good practice always incorporates the reference conditions of temperature and pressure. If not stated, some room environment conditions are supposed, close to 1 atm pressure, 293 K (20 °C), and 0% humidity.

Definitions

In chemistry, IUPAC changed its definition of standard temperature and pressure in 1982:[1][2]

  • Until 1982, STP was defined as a temperature of 273.15 K (0 °C, 32 °F) and an absolute pressure of exactly 1 atm (101.325 kPa).
  • Since 1982, STP has been defined as a temperature of 273.15 K (0 °C, 32 °F) and an absolute pressure of exactly 105 Pa (100 kPa, 1 bar).

NIST uses a temperature of 20 °C (293.15 K, 68 °F) and an absolute pressure of 1 atm (14.696 psi, 101.325 kPa).[3] This standard is also called normal temperature and pressure (abbreviated as NTP). However, a common temperature and pressure in use by NIST for thermodynamic experiments is 298.15 K (25°C, 77°F) and 1 bar (14.5038 psi, 100 kPa).[4][5] NIST also uses "15 °C (59 °F)" for the temperature compensation of refined petroleum products, despite noting that these two values are not exactly consistent with each other.[6]

The ISO 13443 standard reference conditions for natural gas and similar fluids are 288.15 K (15.00 °C; 59.00 °F) and 101.325 kPa;[7] by contrast, the American Petroleum Institute adopts 60 °F (15.56 °C; 288.71 K).[8]

Past uses

Before 1918, many professionals and scientists using the metric system of units defined the standard reference conditions of temperature and pressure for expressing gas volumes as being 15 °C (288.15 K; 59.00 °F) and 101.325 kPa (1.00 atm; 760 Torr). During those same years, the most commonly used standard reference conditions for people using the imperial or U.S. customary systems was 60 °F (15.56 °C; 288.71 K) and 14.696 psi (1 atm) because it was almost universally used by the oil and gas industries worldwide. The above definitions are no longer the most commonly used in either system of units.[9]

Current use

Many different definitions of standard reference conditions are currently being used by organizations all over the world. The table below lists a few of them, but there are more. Some of these organizations used other standards in the past. For example, IUPAC has, since 1982, defined standard reference conditions as being 0 °C and 100 kPa (1 bar), in contrast to its old standard of 0 °C and 101.325 kPa (1 atm).[2] The new value is the mean atmospheric pressure at an altitude of about 112 metres, which is closer to the worldwide median altitude of human habitation (194 m).[10]

Natural gas companies in Europe, Australia, and South America have adopted 15 °C (59 °F) and 101.325 kPa (14.696 psi) as their standard gas volume reference conditions, used as the base values for defining the standard cubic meter.[11][12][13] Also, the International Organization for Standardization (ISO), the United States Environmental Protection Agency (EPA) and National Institute of Standards and Technology (NIST) each have more than one definition of standard reference conditions in their various standards and regulations.

Standard reference conditions in current use
Temperature Pressure Density Relative
humidity

(%)
Publishing or establishing entity
°C °F kPa mmHg psi inHg kg/m³
0 32 100.000 750.06 14.5038 29.530   IUPAC (STP) since 1982[1]
0 32 101.325 760.00 14.6959 29.921
15 59 101.325 760.00 14.6959 29.921 1.225 0[7][14] ICAO's ISA,[14] ISO 13443,[7] EEA,[15] EGIA (SI Definition)[16]
20 68 101.325 760.00 14.6959 29.921   EPA,[17] NIST.[18] This is also called NTP, Normal Temperature and Pressure.[19]
22 71.6 101.325 760.00 14.6959 29.921 20–80 American Association of Physicists in Medicine[20]


25 77 101.325 760.00 14.6959 29.921   SATP,[21] EPA[22]
20 68 100.000 750.06 14.5038 29.530 0 CAGI[23]
15 59 100.000 750.06 14.5038 29.530   SPE[24]
20 68 101.3 760 14.69 29.9 50 ISO 5011[25]
20 68 101.33 760.0 14.696 29.92 0 GOST 2939-63
15.56 60 101.33 760.0 14.696 29.92   SPE,[24] U.S. OSHA,[26] SCAQMD[27]
15.56 60 101.6 762 14.73 30.0   EGIA (Imperial System Definition)[16]
15.56 60 101.35 760.21 14.7 29.93   U.S. DOT (SCF)[28]
15 59 99.99 750.0 14.503 29.53 78 U.S. Army Standard Metro[29][lower-alpha 1]
15 59 101.33 760.0 14.696 29.92 60 ISO 2314,[30] ISO 3977-2,[31] ASHRAE Fundamentals Handbook[32]
21.11 70 101.3 760 14.70 29.92 0 AMCA,[33][lower-alpha 2] air density = 0.075 lbm/ft3. This AMCA standard applies only to air;
Compressed Gas Association [CGA] applies to industrial gas use in US[34]
15 59 101.3 760 14.70 29.92   FAA[35]
20 68 101.325 760.00 14.6959 29.921 0 EN 14511-1:2013[36]
15 59 101.325 760.00 14.6959 29.921 0 ISO 2533:1975[37] ISO 13443:2005,[38] ISO 7504:2015[39]
0 32 101.325 760.00 14.6959 29.921 0 DIN 1343:1990[40]

Abbreviations:

  • EGIA: Electricity and Gas Inspection Act (of Canada)
  • SATP: Standard Ambient Temperature and Pressure
  • SCF: Standard Cubic Foot

International Standard Atmosphere

In aeronautics and fluid dynamics the "International Standard Atmosphere" (ISA) is a specification of pressure, temperature, density, and speed of sound at each altitude. The International Standard Atmosphere is representative of atmospheric conditions at mid latitudes. In the US this information is specified the U.S. Standard Atmosphere which is identical to the "International Standard Atmosphere" at all altitudes up to 65,000 feet above sea level.[citation needed]

Standard laboratory conditions

Because many definitions of standard temperature and pressure differ in temperature significantly from standard laboratory temperatures (e.g. 0 °C vs. ~25 °C), reference is often made to "standard laboratory conditions" (a term deliberately chosen to be different from the term "standard conditions for temperature and pressure", despite its semantic near identity when interpreted literally). However, what is a "standard" laboratory temperature and pressure is inevitably geography-bound, given that different parts of the world differ in climate, altitude and the degree of use of heat/cooling in the workplace. For example, schools in New South Wales, Australia use 25 °C at 100 kPa for standard laboratory conditions.[41] ASTM International has published Standard ASTM E41- Terminology Relating to Conditioning and hundreds of special conditions for particular materials and test methods. Other standards organizations also have specialized standard test conditions.[citation needed]

Molar volume of a gas

It is as important to indicate the applicable reference conditions of temperature and pressure when stating the molar volume of a gas[42] as it is when expressing a gas volume or volumetric flow rate. Stating the molar volume of a gas without indicating the reference conditions of temperature and pressure has very little meaning and can cause confusion.

The molar volume of gases around STP and at atmospheric pressure can be calculated with an accuracy that is usually sufficient by using the ideal gas law. The molar volume of any ideal gas may be calculated at various standard reference conditions as shown below:

  • Vm = 8.3145 × 273.15 / 101.325 = 22.414 dm3/mol at 0 °C and 101.325 kPa
  • Vm = 8.3145 × 273.15 / 100.000 = 22.711 dm3/mol at 0 °C and 100 kPa
  • Vm = 8.3145 × 288.15 / 101.325 = 23.645 dm3/mol at 15 °C and 101.325 kPa
  • Vm = 8.3145 × 298.15 / 101.325 = 24.466 dm3/mol at 25 °C and 101.325 kPa
  • Vm = 8.3145 × 298.15 / 100.000 = 24.790 dm3/mol at 25 °C and 100 kPa
  • Vm = 10.7316 × 519.67 / 14.696 = 379.48 ft3/lbmol at 60 °F and 14.696 psi (or about 0.8366 ft3/gram mole)
  • Vm = 10.7316 × 519.67 / 14.730 = 378.61 ft3/lbmol at 60 °F and 14.73 psi

Technical literature can be confusing because many authors fail to explain whether they are using the ideal gas constant R, or the specific gas constant Rs. The relationship between the two constants is Rs = R / m, where m is the molecular mass of the gas.

The US Standard Atmosphere (USSA) uses 8.31432 m3·Pa/(mol·K) as the value of R. However, the USSA,1976 does recognize that this value is not consistent with the values of the Avogadro constant and the Boltzmann constant.[43]

See also

Explanatory notes

  1. The pressure is specified as 750 mmHg. However, the mmHg is temperature-dependent, since mercury expands as temperature goes up. Here the values for the 0–20 °C range are given.
  2. The standard is given as 29.92 inHg at an unspecified temperature. This most likely corresponds to a standard pressure of 101.325 kPa, converted into ~29.921 inHg at 32 °F (0 °C).

References

  1. 1.0 1.1 A. D. McNaught and A. Wilkinson (1997). Nič, Miloslav; Jirát, Jiří; Košata, Bedřich et al.. eds. IUPAC. Compendium of Chemical Terminology (2nd ed.). Oxford: Blackwell Scientific Publications. p. 54. doi:10.1351/goldbook. ISBN 0-632-03583-8. https://dev.goldbook.iupac.org/files/pdf/green_book_2ed.pdf#page=62. "Standard conditions for gases: ... and pressure of 105 pascals. The previous standard absolute pressure of 1 atm (equivalent to 101.325 kPa) was changed to 100 kPa in 1982. IUPAC recommends that the former pressure should be discontinued." 
  2. 2.0 2.1 A. D. McNaught and A. Wilkinson (1997). IUPAC. Compendium of Chemical Terminology (2nd ed.). Oxford: Blackwell Scientific Publications. doi:10.1351/goldbook.S05921. ISBN 978-0-9678550-9-7. 
  3. Doiron, Theodore D. (January 2007). "20 Degrees Celsius--A Short History of the Standard Reference Temperature for Industrial Dimensional Measurements". NIST 112 (1): 1–23. doi:10.6028/jres.112.001. PMID 27110451. PMC 4654601. https://www.nist.gov/publications/20-degrees-celsius-short-history-standard-reference-temperature-industrial-dimensional. 
  4. Helrich, Carl S. (2008-11-14) (in en). Modern Thermodynamics with Statistical Mechanics. Springer Science & Business Media. ISBN 978-3-540-85418-0. https://books.google.com/books?id=oU5DICYlDEAC&q=Modern+Thermodynamics+with+Statistical+Mechanics&pg=PA1. 
  5. "A Guide to the NIST Chemistry WebBook". https://webbook.nist.gov/chemistry/guide/index.html.en-us.en. 
  6. "Specifications, Tolerances, and Other Technical Requirements for Weighing and Measuring Devices". p. 3-1. https://www.nist.gov/system/files/documents/2021/05/05/00-20-hb44-web-final_0.pdf. 
  7. 7.0 7.1 7.2 Natural gas – Standard reference conditions (ISO 13443). Geneva, Switzerland: International Organization for Standardization. 1996. http://www.iso.org/iso/iso_catalogue/catalogue_tc/catalogue_detail.htm?csnumber=20461. 
  8. API Petroleum Measurement
  9. Doiron, Ted (Jan–Feb 2007). "20 °C – A Short History of the Standard Reference Temperature for Industrial Dimensional Measurements". Journal of Research of the National Institute of Standards and Technology 112 (1): 1–23. doi:10.6028/jres.112.001. PMID 27110451. 
  10. Cohen, Joel E.; Small, Christopher (November 24, 1998). "Hypsographic demography: The distribution of human population by altitude". Proceedings of the National Academy of Sciences 95 (24): 14009–14014. doi:10.1073/pnas.95.24.14009. PMID 9826643. Bibcode1998PNAS...9514009C. 
  11. Gassco. "Concepts – Standard cubic meter (scm)". http://www.gassco.no/sw3138.asp. "Scm: The usual abbreviation for standard cubic metre – a cubic metre of gas under a standard condition, defined as an atmospheric pressure of 1.01325 bar and a temperature of 15°C. This unit provides a measure for gas volume." 
  12. Nord Stream (October 2007). "Status of the Nord Stream pipeline route in the Baltic Sea". http://www.nord-stream.com/uploads/media/Nord_Stream_Route_Status_ENGLISH.pdf. "bcm: Billion Cubic Meter (standard cubic metre – a cubic metre of gas under a standard condition, defined as an atmospheric pressure of 1 atm and a temperature of 15 °C.)" 
  13. Metrogas (June 2004). "Natural gas purchase and sale agreement". http://www.secinfo.com/dsD7y.1a.7.htm. "Natural gas at standard condition shall mean the quantity of natural gas, which at a temperature of fifteen (15) Celsius degrees and a pressure of 101.325 kilopascals occupies the volume of one (1) cubic meter." 
  14. 14.0 14.1 Robert C. Weast, ed (1975). Handbook of Physics and Chemistry (56th ed.). CRC Press. pp. F201–F206. ISBN 978-0-87819-455-1. 
  15. (PDF) Extraction, First Treatment and Loading of Liquid & Gaseous Fossil Fuels (Emission Inventory Guidebook B521, Activities 050201 – 050303). Copenhagen, Denmark: European Environmental Agency. September 1999. https://www.eea.europa.eu/publications/EMEPCORINAIR3/B521vs3.1.pdf/view. 
  16. 16.0 16.1 "Electricity and Gas Inspection Act", SOR/86-131 (defines a set of standard conditions for Imperial units and a different set for metric units)  Canadian Laws.
  17. "Standards of Performance for New Sources", 40 CFR—Protection of the Environment, Chapter I, Part 60, Section 60.2, 1990.
  18. Wright, J. D.; Johnson, A. N.; Moldover, M. R. (2003). "Design and Uncertainty for a PVTt Gas Flow Standard". Journal of Research of the National Institute of Standards and Technology 108 (1): 21–47. doi:10.6028/jres.108.004. PMID 27413592. PMC 4844527. http://www.cstl.nist.gov/div836/836.01/PDFs/2003/j80wri.pdf. 
  19. "What is the difference between STP and NTP?". http://socratic.org/questions/what-is-the-difference-between-stp-and-ntp. 
  20. Almond, Peter R.; Biggs, Peter J.; Coursey, B. M.; Hanson, W. F.; Huq, M. Saiful; Nath, Ravinder; Rogers, D. W. O. (1999). "AAPM's TG-51 protocol for clinical reference dosimetry of high-energy photon and electron beams". Medical Physics 26 (9): 1847–1870. doi:10.1118/1.598691. PMID 10505874. Bibcode1999MedPh..26.1847A. 
  21. "CRC Handbook of Chemistry and Physics", Definition of Ambient, Chapter 1-26, 95th Edition, William M. Haynes, ed., CRC Press, Boca Raton, FL, 2014.
  22. "National Primary and Secondary Ambient Air Quality Standards", 40 CFR—Protection of the Environment, Chapter I, Part 50, Section 50.3, 1998.
  23. "Glossary". Cleveland, OH, US: Compressed Air and Gas Institute. 2002. http://www.cagi.org/toolbox/glossary.htm. 
  24. 24.0 24.1 "The SI Metric System of Units and SPE Metric Standard (1982)". Society of Petroleum Engineers. Standard Temperature (Page 24), and Notes for Table 2.3, (on PDF page 25 of 42 PDF pages), define two different sets of reference conditions, one for the standard cubic foot and one for the standard cubic meter. https://www.spe.org/authors/docs/metric_standard.pdf. 
  25. Air Intake Filters (ISO 5011:2002). Geneva, Switzerland: International Organization for Standardization. 2002. http://www.iso.org/iso/en/prods-services/ISOstore/store.html. 
  26. "Storage and Handling of Liquefied Petroleum Gases" and "Storage and Handling of Anhydrous Ammonia", 29 CFR—Labor, Chapter XVII—Occupational Safety and Health Administration, Part 1910, Sect. 1910.110 and 1910.111, 1993  Storage/Handling of LPG.
  27. "Rule 102, Definition of Terms (Standard Conditions)", Amended December 2004, South Coast Air Quality Management District, Los Angeles, California, US  SCAQMD Rule 102
  28. "49 C.F.R. § 171". https://www.ecfr.gov/cgi-bin/text-idx?SID=4cb9c4fbd569caade0b61e28dec528f2&mc=true&node=se49.2.171_18&rgn=div8. 
  29. Sierra Bullets. "Chapter 3 – Effects of Altitude and Atmospheric Conditions (Exterior Ballistics Section)". Rifle and Handgun Reloading Manual (5 ed.). Sedalia, MO, US. http://www.exteriorballistics.com/ebexplained/5th/31.cfm. Retrieved 2006-02-03. 
  30. Gas turbines – Acceptance tests (ISO 2314:2009) (2 ed.). Geneva, Switzerland: International Organization for Standardization. 2009. https://www.iso.org/standard/42989.html. 
  31. Gas turbines – Procurement – Part 2: Standard reference conditions and ratings (ISO 3977-2:1997). Geneva, Switzerland: International Organization for Standardization. 1997. https://www.iso.org/standard/24755.html. 
  32. "ASHRAE Handbook Online". https://www.ashrae.org/technical-resources/ashrae-handbook/ashrae-handbook-online. 
  33. ANSI/AMCA Standard 210, "Laboratory Methods Of Testing Fans for Aerodynamic Performance Rating", as implied by http://www.greenheck.com/pdf/centrifugal/Plug.pdf when accessed on October 17, 2007.
  34. Association, Compressed Gas (2012-12-06). Compressed Gas Handbook. Springer. ISBN 9781461306733. https://books.google.com/books?id=5EfhBwAAQBAJ&q=%22compressed+gas+association%22+handbook+fifth+edition. Retrieved 22 Nov 2017. 
  35. Pilot's Handbook of Aeronautical Knowledge. U.S. Department of Transportation Federal Aviation Administration. 2016. p. 4-3. https://www.faa.gov/sites/faa.gov/files/2022-03/pilot_handbook.pdf. 
  36. Air Conditioners, liquid chilling packages and heat pumps with electrically driven compressors for space heating and cooling. UK: BSI EN. 2013. https://shop.bsigroup.com/ProductDetail/?pid=000000000030271396. 
  37. Standard Atmosphere. Geneva, Switzerland: International Organization for Standardization. 1975. https://www.iso.org/standard/7472.html. 
  38. Natural gas - Standard reference conditions. Geneva, Switzerland: International Organization for Standardization. 1996. https://www.iso.org/standard/20461.html. 
  39. Gas analysis - Vocabulary. Geneva, Switzerland: International Organization for Standardization. 2015. https://www.iso.org/standard/53596.html. 
  40. Referenzzustand, Normzustand, Normvolumen; Begriffe und Werte. Germany: Deutsches Institut für Normung. 1990. https://www.din.de/en/getting-involved/standards-committees/natg/standards/wdc-beuth:din21:1505240. 
  41. Peter Gribbon (2001). Excel HSC Chemistry Pocket Book Years 11–12. Pascal Press. ISBN 978-1-74020-303-6. 
  42. "Fundamental Physical Properties: Molar Volumes (CODATA values for ideal gases)". NIST. http://physics.nist.gov/cgi-bin/cuu/Results?search_for=volume+molar. 
  43. U.S. Standard Atmosphere, 1976, U.S. Government Printing Office, Washington, D.C., 1976.

External links