List of ISO standards 14000–15999

From HandWiki
Short description: none
Main page: List of ISO standards

This is a list of published[Note 1] International Organization for Standardization (ISO) standards and other deliverables.[Note 2] For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.[1]

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.[2]

ISO 14000 – ISO 14999

  • ISO 14000 Environmental management systems (This is a set of standards, rather than a single standard)
  • ISO 14001:2015 Environmental management systems – Requirements with guidance for use
  • ISO 14004:2016 Environmental management systems – General guidelines on implementation
  • ISO 14005:2010 Environmental management systems – Guidelines for the phased implementation of an environmental management system, including the use of environmental performance evaluation
  • ISO 14006:2011 Environmental management systems – Guidelines for incorporating ecodesign
  • ISO 14015:2022 Environmental management — Guidelines for environmental due diligence assessment
  • ISO 14020:2000 Environmental labels and declarations – General principles
  • ISO 14031 Environmental management - Environmental performance evaluation – Guidelines
  • ISO 14045:2012 describes the principles, requirements and guidelines for eco-efficiency assessment for product systems [3]
  • ISO 14046:2014 - Environmental management — Water footprint — Principles, requirements and guidelines
  • ISO 14050:2009 Environmental management – Vocabulary
  • ISO 14051 Environmental management – Material flow cost accounting - General framework
  • ISO 14064 Greenhouse gases
  • ISO/TR 14073:2017 Environmental management - Water footprint - Illustrative examples on how to apply ISO 14046
  • ISO 14084 Process diagrams for power plants
    • ISO 14084-1:2015 Part 1: Specification for diagrams
    • ISO 14084-2:2015 Part 2: Graphical symbols
  • ISO/TS 14101:2012 Surface characterization of gold nanoparticles for nanomaterial specific toxicity screening: FT-IR method
  • ISO/IEC 14102:2008 Information technology - Guideline for the evaluation and selection of CASE tools
  • ISO/TR 14105:2011 Document management - Change management for successful electronic document management system (EDMS) implementation
  • ISO 14117:2012 Active implantable medical devices – Electromagnetic compatibility – EMC test protocols for implantable cardiac pacemakers, implantable cardioverter defibrillators and cardiac resynchronization devices
  • ISO 14132 Optics and photonics - Vocabulary for telescopic systems
    • ISO 14132-1:2015 Part 1: General terms and alphabetical indexes of terms in ISO 14132
    • ISO 14132-2:2015 Part 2: Terms for binoculars, monoculars and spotting scopes
    • ISO 14132-3:2014 Part 3: Terms for telescopic sights
    • ISO 14132-4:2015 Part 4: Terms for astronomical telescopes
    • ISO 14132-5:2008 Part 5: Terms for night vision devices
  • ISO/IEC 14136:1995 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Identification supplementary services
  • ISO 14139:2000 Hydrometric determinations – Flow measurements in open channels using structures – Compound gauging structures
  • ISO/IEC 14143 Information technology - Software measurement - Functional size measurement
    • ISO/IEC 14143-1:2007 Part 1: Definition of concepts
    • ISO/IEC 14143-2:2011 Part 2: Conformity evaluation of software size measurement methods to ISO/IEC 14143-1
    • ISO/IEC TR 14143-3:2003 Part 3: Verification of functional size measurement methods
    • ISO/IEC TR 14143-4:2002 Part 4: Reference model
    • ISO/IEC TR 14143-5:2004 Part 5: Determination of functional domains for use with functional size measurement
    • ISO/IEC 14143-6:2012 Part 6: Guide for use of ISO/IEC 14143 series and related International Standards
  • ISO 14145 Roller ball pens and refills
    • ISO 14145-2:1998 Part 2: Documentary use (DOC)
  • ISO 14155:2011 Clinical investigation of medical devices for human subjects – Good clinical practice
  • ISO 14163:1998 Acoustics – Guidelines for noise control by silencers
  • ISO 14164:1999 Stationary source emissions – Determination of the volume flowrate of gas streams in ducts – Automated method
  • ISO/IEC 14165 Information technology - Fibre Channel
    • ISO/IEC 14165-114:2005 Part 114: 100 MB/s Balanced copper physical interface (FC-100-DF-EL-S)
    • ISO/IEC 14165-115:2006 Part 115: Physical Interfaces (FC-PI)
    • ISO/IEC 14165-116:2005 Part 116: 10 Gigabit (10GFC)
    • ISO/IEC TR 14165-117:2007 Part 117: Methodologies for jitter and signal quality (MJSQ)
    • ISO/IEC 14165-122:2005 Part 122: Arbitrated Loop-2 (FC-AL-2)
    • ISO/IEC 14165-131:2000 Part 131: Switch Fabric Requirements (FC-SW)
    • ISO/IEC 14165-133:2010 Part 133: Switch Fabric-3 (FC-SW-3)
    • ISO/IEC 14165-141:2001 Part 141: Fabric Generic Requirements (FC-FG)
    • ISO/IEC 14165-211:1999 Part 211: Mapping to HIPPI-FP (FC-FP)
    • ISO/IEC 14165-222:2005 Part 222: Single-byte command code 2 mapping protocol (FC-SB-2)
    • ISO/IEC 14165-241:2005 Part 241: Backbone 2 (FC-BB-2)
    • ISO/IEC 14165-243:2012 Part 243: Backbone 3 (FC-BB-3)
    • ISO/IEC 14165-251:2008 Part 251: Framing and Signaling (FC-FS)
    • ISO/IEC TR 14165-312:2009 Part 312: Avionics environment upper layer protocol MIL-STD-1553B Notice 2 (FC-AE-1553)
    • ISO/IEC TR 14165-313:2013 Part 313: Avionics Environment—Anonymous Synchronous Messaging (FC-AE-ASM)
    • ISO/IEC TR 14165-314:2013 Part 314: Avionics Environment – Remote Direct Memory Access (FC-AE-RDMA)
    • ISO/IEC 14165-321:2009 Part 321: Audio-Video (FC-AV)
    • ISO/IEC 14165-331:2007 Part 331: Virtual Interface (FC-VI)
    • ISO/IEC TR 14165-372:2011 Part 372: Methodologies of interconnects-2 (FC-MI-2)
    • ISO/IEC 14165-414:2007 Part 414: Generic Services—4 (FC-GS-4)
    • ISO/IEC 14165-521:2009 Part 521: Fabric application interface standard (FAIS)
  • ISO/IEC 14169:1995 Information technology – 90 mm flexible disk cartridges – 21 MBytes formatted capacity – ISO Type 305
  • ISO 14189:2013 Water quality – Enumeration of Clostridium perfringens – Method using membrane filtration
  • ISO 14199:2015 Health informatics – Information models – Biomedical Research Integrated Domain Group (BRIDG) Model
  • ISO 14223 identification of animals – Advanced transponders
  • ISO 14224 Petroleum, petrochemical and natural gas industries - Collection and exchange of reliability and maintenance data for equipment
  • ISO 14230 Road vehicles – Diagnostic systems – Keyword Protocol 2000
  • ISO 14242 Implants for surgery – Wear of total hip-joint prostheses
    • ISO 14242-1:2014 Part 1: Loading and displacement parameters for wear-testing machines and corresponding environmental conditions for test
    • ISO 14242-2:2016 Part 2: Methods of measurement
    • ISO 14242-3:2009 Part 3: Loading and displacement parameters for orbital bearing type wear testing machines and corresponding environmental conditions for test
  • ISO 14243 Implants for surgery – Wear of total knee-joint prostheses
    • ISO 14243-1:2009 Part 1: Loading and displacement parameters for wear-testing machines with load control and corresponding environmental conditions for test
    • ISO 14243-2:2016 Part 2: Methods of measurement
    • ISO 14243-3:2014 Part 3: Loading and displacement parameters for wear-testing machines with displacement control and corresponding environmental conditions for test
  • ISO/IEC 14251:1995 Information technology – Data interchange on 12,7 mm 36-track magnetic tape cartridges
  • ISO/IEC TR 14252:1996 Information technology - Guide to the POSIX Open System Environment (OSE) [Withdrawn without replacement]
  • ISO 14253 Geometrical product specifications (GPS) - Inspection by measurement of workpieces and measuring equipment
    • ISO 14253-1:2013 Part 1: Decision rules for proving conformity or nonconformity with specifications
    • ISO 14253-2:2011 Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification
    • ISO 14253-3:2011 Part 3: Guidelines for achieving agreements on measurement uncertainty statements
    • ISO/TS 14253-4:2010 Part 4: Background on functional limits and specification limits in decision rules
    • ISO 14253-5:2015 Part 5: Uncertainty in verification testing of indicating measuring instruments
    • ISO/TR 14253-6:2012 Part 6: Generalized decision rules for the acceptance and rejection of instruments and workpieces
  • ISO/TS 14265:2011 Health Informatics – Classification of purposes for processing personal health information
  • ISO/TR 14283:2004 Implants for surgery – Fundamental principles
  • ISO 14289 Document management applications - Electronic document file format enhancement for accessibility
    • ISO 14289-1:2014 Part 1: Use of ISO 32000-1 (PDF/UA-1)
  • ISO/TR 14292:2012 Health informatics – Personal health records – Definition, scope and context
  • ISO 14296:2016 Intelligent transport systems – Extension of map database specifications for applications of cooperative ITS
  • ISO 14302:2002 Space systems – Electromagnetic compatibility requirements
  • ISO 14362 Textiles - Methods for determination of certain aromatic amines derived from azo colorants
    • ISO 14362-1:2017 Part 1: Detection of the use of certain azo colorants accessible with and without extracting the fibres
    • ISO 14362-3:2017 Part 3: Detection of the use of certain azo colorants, which may release 4-aminoazobenzene
  • ISO/IEC TR 14369:2018 Information technology – Programming languages, their environments and system software interfaces – Guidelines for the preparation of language-independent service specifications (LISS)
  • ISO 14405 Geometrical product specifications (GPS) – Dimensional tolerancing
    • ISO 14405-1:2016 Part 1: Linear sizes
    • ISO 14405-2:2011 Part 2: Dimensions other than linear sizes
    • ISO 14405-3:2016 Part 3: Angular sizes
  • ISO 14406:2010 Geometrical product specifications (GPS) - Extraction
  • ISO 14408:2016 Tracheal tubes designed for laser surgery – Requirements for marking and accompanying information
  • ISO 14416:2003 Information and documentation – Requirements for binding of books, periodicals, serials and other paper documents for archive and library use – Methods and materials
  • ISO/IEC 14417:1999 Information technology – Data recording format DD-1 for magnetic tape cassette conforming to IEC 1016
  • ISO/TS 14441:2013 Health informatics – Security and privacy requirements of EHR systems for use in conformity assessment
  • ISO/IEC 14443 Identification cards – Contactless integrated circuit cards – Proximity cards
  • ISO 14451 Pyrotechnic articles – Pyrotechnic articles for vehicles
    • ISO 14451-1:2013 Part 1: Terminology
  • ISO 14452:2012 Network services billing – Requirements
  • ISO 14461 Milk and milk products – Quality control in microbiological laboratories
    • ISO 14461-1:2005 Part 1: Analyst performance assessment for colony counts
    • ISO 14461-2:2005 Part 2: Determination of the reliability of colony counts of parallel plates and subsequent dilution steps
  • ISO/IEC 14462:2010 Information technology - Open-edi reference model
  • ISO/TR 14468:2010 Selected illustrations of attribute agreement analysis
  • ISO/IEC TR 14471:2007 Information technology - Software engineering - Guidelines for the adoption of CASE tools
  • ISO/IEC 14473:1999 Information technology - Office equipment - Minimum information to be specified for image scanners
  • ISO/IEC 14474:1998 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Functional requirements for static circuit-mode inter-PINX connections
  • ISO/IEC TR 14475:2001 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Architecture and scenarios for Private Integrated Services Networking
  • ISO/IEC 14476 Information technology – Enhanced communications transport protocol
    • ISO/IEC 14476-1:2002 Specification of simplex multicast transport
    • ISO/IEC 14476-2:2003 Specification of QoS management for simplex multicast transport
    • ISO/IEC 14476-3:2008 Specification of duplex multicast transport
    • ISO/IEC 14476-4:2010 Specification of QoS management for duplex multicast transport
    • ISO/IEC 14476-5:2008 Specification of N-plex multicast transport
    • ISO/IEC 14476-6:2010 Specification of QoS management for n-plex multicast transport
  • ISO/IEC 14478 Information technology - Computer graphics and image processing - Presentation Environment for Multimedia Objects (PREMO)
    • ISO/IEC 14478-1:1998 Part 1: Fundamentals of PREMO
    • ISO/IEC 14478-2:1998 Part 2: Foundation Component
    • ISO/IEC 14478-3:1998 Part 3: Multimedia Systems Services
    • ISO/IEC 14478-4:1998 Part 4: Modelling, rendering and interaction component
  • ISO/IEC 14492:2001 Information technology - Lossy/lossless coding of bi-level images
  • ISO/IEC 14495 Information technology - Lossless and near-lossless compression of continuous-tone still images
    • ISO/IEC 14495-1:1999 Baseline
    • ISO/IEC 14495-2:2003 Extensions
  • ISO/IEC 14496 Information technology – Coding of audio-visual objects
  • ISO 14500:2003 Textile machinery and accessories – Harnesses for Jacquard weaving machines – Vocabulary
  • ISO 14509 Small craft – Airborne sound emitted by powered recreational craft
    • ISO 14509-1:2008 Part 1: Pass-by measurement procedures
    • ISO 14509-3:2009 Part 3: Sound assessment using calculation and measurement procedures
  • ISO 14511:2001 Measurement of fluid flow in closed conduits – Thermal mass flowmeters
  • ISO/IEC 14515 Information technology - Portable Operating System Interface (POSIX®) - Test methods for measuring conformance to POSIX
    • ISO/IEC 14515-1:2000 Part 1: System interfaces
  • ISO/IEC TR 14516:2002 Information technology - Security techniques - Guidelines for the use and management of Trusted Third Party services
  • ISO/IEC 14517:1996 Information technology - 130 mm optical disk cartridges for information interchange - Capacity: 2,6 Gbytes per cartridge
  • ISO/IEC 14519:2001 Information technology - POSIX Ada Language Interfaces - Binding for System Application Program Interface (API)
  • ISO 14532:2014 Natural gas – Vocabulary
  • ISO 14533 Processes, data elements and documents in commerce, industry and administration – Long term signature profiles
    • ISO 14533-1:2014 Part 1: Long term signature profiles for CMS Advanced Electronic Signatures (CAdES)
    • ISO 14533-2:2012 Part 2: Long term signature profiles for XML Advanced Electronic Signatures (XAdES)
    • ISO 14533-3:2017 Part 3: Long term signature profiles for PDF Advanced Electronic Signatures (PAdES)
  • ISO 14534:2011 Ophthalmic optics – Contact lenses and contact lens care products – Fundamental requirements
  • ISO 14539:2000 Manipulating industrial robots - Object handling with grasp-type grippers - Vocabulary and presentation of characteristics
  • ISO/IEC 14543 Information technology – Home Electronic System (HES) architecture
    • ISO/IEC 14543-2-1:2006 Part 2-1: Introduction and device modularity
    • ISO/IEC 14543-3-1:2006 Part 3-1: Communication layers – Application layer for network based control of HES Class 1
    • ISO/IEC 14543-3-2:2006 Part 3-2: Communication layers – Transport, network and general parts of data link layer for network based control of HES Class 1
    • ISO/IEC 14543-3-3:2007 Part 3-3: User process for network based control of HES Class 1
    • ISO/IEC 14543-3-4:2007 Part 3-4: System management – Management procedures for network based control of HES Class 1
    • ISO/IEC 14543-3-5:2007 Part 3-5: Media and media dependent layers – Power line for network based control of HES Class 1
    • ISO/IEC 14543-3-6:2007 Part 3-6: Media and media dependent layers – Network based on HES Class 1, twisted pair
    • ISO/IEC 14543-3-7:2007 Part 3-7: Media and media dependent layers – Radio frequency for network based control of HES Class 1
    • ISO/IEC 14543-3-10:2012 Part 3-10: Wireless short-packet (WSP) protocol optimized for energy harvesting – Architecture and lower layer protocols
    • ISO/IEC 14543-3-11:2016 Part 3-11: Frequency modulated wireless short-packet (FMWSP) protocol optimised for energy harvesting – Architecture and lower layer protocols
    • ISO/IEC TR 14543-4:2002 Part 4: Home and building automation in a mixed-use building
    • ISO/IEC 14543-4-1:2008 Part 4-1: Communication layers – Application layer for network enhanced control devices of HES Class 1
    • ISO/IEC 14543-4-2:2008 Part 4-2: Communication layers – Transport, network and general parts of data link layer for network enhanced control devices of HES Class 1
    • ISO/IEC 14543-4-3:2015 Part 4-3: Application layer interface to lower communications layers for network enhanced control devices of HES Class 1
    • ISO/IEC 14543-5-1:2010 Part 5-1: Intelligent grouping and resource sharing for Class 2 and Class 3 – Core protocol
    • ISO/IEC 14543-5-3:2012 Part 5-3: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Basic application
    • ISO/IEC 14543-5-4:2010 Part 5-4: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Device validation
    • ISO/IEC 14543-5-5:2012 Part 5-5: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Device type
    • ISO/IEC 14543-5-6:2012 Part 5-6: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Service type
    • ISO/IEC 14543-5-7:2015 Part 5-7: Intelligent grouping and 3 resource sharing – Remote access system architecture
    • ISO/IEC 14543-5-8:2017 Part 5-8: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Remote access core protocol
    • ISO/IEC 14543-5-9:2017 Part 5-9: Intelligent grouping and resource sharing for HES class 2 and class 3 – Remote access service platform
    • ISO/IEC 14543-5-21:2012 Part 5-21: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Application profile – AV profile
    • ISO/IEC 14543-5-22:2010 Part 5-22: Intelligent grouping and resource sharing for HES Class 2 and Class 3 – Application profile – File profile
  • ISO 14560:2004 Acceptance sampling procedures by attributes - Specified quality levels in nonconforming items per million
  • ISO/TR 14564:1995 Shipbuilding and marine structures - Marking of escape routes
  • ISO/IEC 14568:1997 Information technology - DXL: Diagram eXchange Language for tree-structured charts
  • ISO/IEC 14575:2000 Information technology - Microprocessor systems - Heterogeneous InterConnect (HIC) (Low-Cost, Low-Latency Scalable Serial Interconnect for Parallel System Construction)
  • ISO/IEC 14576:1999 Information technology - Synchronous Split Transfer Type System Bus (STbus) - Logical Layer
  • ISO 14580:2011 Hexalobular socket cheese head screws
  • ISO 14588:2000 Blind rivets - Terminology and definitions
  • ISO/IEC 14598 Software engineering - Product evaluation[Note 3]
    • ISO/IEC 14598-5:1998 Part 5: Process for evaluators
    • ISO/IEC 14598-6:2001 Part 6: Documentation of evaluation modules
  • ISO 14602:2010 Non-active surgical implants – Implants for osteosynthesis – Particular requirements
  • ISO 14607:2007 Non-active surgical implants – Mammary implants – Particular requirements
  • ISO 14617 Graphical symbols for diagrams
    • ISO 14617-1:2005 Part 1: General information and indexes
    • ISO 14617-2:2002 Part 2: Symbols having general application
    • ISO 14617-3:2002 Part 3: Connections and related devices
    • ISO 14617-3:2002 Part 3: Connections and related devices
    • ISO 14617-4:2002 Part 4: Actuators and related devices
    • ISO 14617-5:2002 Part 5: Measurement and control devices
    • ISO 14617-6:2002 Part 6: Measurement and control functions
    • ISO 14617-7:2002 Part 7: Basic mechanical components
    • ISO 14617-8:2002 Part 8: Valves and dampers
    • ISO 14617-9:2002 Part 9: Pumps, compressors and fans
    • ISO 14617-10:2002 Part 10: Fluid power converters
    • ISO 14617-11:2002 Part 11: Devices for heat transfer and heat engines
    • ISO 14617-12:2002 Part 12: Devices for separating, purification and mixing
    • ISO 14617-13:2004 Part 13: Devices for material processing
    • ISO 14617-14:2004 Part 14: Devices for transport and handling of material
    • ISO 14617-15:2002 Part 15: Installation diagrams and network maps
  • ISO 14630:2012 Non-active surgical implants – General requirements
  • ISO 14638:2015 Geometrical product specifications (GPS) - Matrix model
  • ISO/TR 14639 Health informatics – Capacity-based eHealth architecture roadmap
    • ISO/TR 14639-1:2012 Part 1: Overview of national eHealth initiatives
    • ISO/TR 14639-2:2014 Part 2: Architectural components and maturity model
  • ISO 14641 Electronic archiving
    • ISO 14641-1:2012 Specifications concerning the design and the operation of an information system for electronic information preservation
  • ISO 14644 Cleanrooms and associated controlled environments
  • ISO/IEC 14651:2020 Information technology — International string ordering and comparison — Method for comparing character strings and description of the common template tailorable ordering
  • ISO/IEC 14662:2010 Information technology – Open-edi reference model
  • ISO/TR 14685:2001 Hydrometric determinations – Geophysical logging of boreholes for hydrogeological purposes – Considerations and guidelines for making measurements
  • ISO 14686:2003 Hydrometric determinations – Pumping tests for water wells – Considerations and guidelines for design, performance and use
  • ISO 14695:2003 Industrial fans – Method of measurement of fan vibration
  • ISO 14698 Cleanrooms and associated controlled environments – Biocontamination control
    • ISO 14698-1:2003 General principles and methods
    • ISO 14698-2:2003 Evaluation and interpretation of biocontamination data
  • ISO/IEC 14699:1997 Information technology – Open Systems Interconnection – Transport Fast Byte Protocol
  • ISO/IEC 14700:1997 Information technology – Open Systems Interconnection – Network Fast Byte Protocol
  • ISO 14708 Implants for surgery – Active implantable medical devices
    • ISO 14708-1:2014 Part 1: General requirements for safety, marking and for information to be provided by the manufacturer
    • ISO 14708-2:2012 Part 2: Cardiac pacemakers
    • ISO 14708-3:2017 Part 3: Implantable neurostimulators
    • ISO 14708-4:2008 Part 4: Implantable infusion pumps
    • ISO 14708-5:2010 Part 5: Circulatory support devices
    • ISO 14708-6:2010 Part 6: Particular requirements for active implantable medical devices intended to treat tachyarrhythmia (including implantable defibrillators)
    • ISO 14708-7:2013 Part 7: Particular requirements for cochlear implant systems
  • ISO/IEC 14709 Information technology - Configuration of Customer Premises Cabling (CPC) for applications
  • ISO 14722:1998 Moped and moped-rider kinematics – Vocabulary
  • ISO 14726:2008 Ships and marine technology – Identification colours for the content of piping systems
  • ISO 14729:2001 Ophthalmic optics – Contact lens care products – Microbiological requirements and test methods for products and regimens for hygienic management of contact lenses
  • ISO 14730:2014 Ophthalmic optics – Contact lens care products – Antimicrobial preservative efficacy testing and guidance on determining discard date
  • ISO 14739 Document management - 3D use of Product Representation Compact (PRC) format
    • ISO 14739-1:2014 Part 1: PRC 10001
  • ISO/TR 14742:2010 Financial services – Recommendations on cryptographic algorithms and their use
  • ISO/IEC 14750:1999 Information technology – Open Distributed Processing – Interface Definition Language
  • ISO/IEC 14752:2000 Information technology - Open Distributed Processing - Protocol support for computational interactions
  • ISO/IEC 14753:1999 Information technology - Open Distributed Processing - Interface references and binding
  • ISO/IEC 14754:1999 Information technology – Pen-Based Interfaces – Common gestures for Text Editing with Pen-Based Systems
  • ISO/IEC 14755:1997 Information technology – Input methods to enter characters from the repertoire of ISO/IEC 10646 with a keyboard or other input device
  • ISO/IEC 14756:1999 Information technology - Measurement and rating of performance of computer-based software systems
  • ISO/IEC 14760:1997 Information technology - Data interchange on 90 mm overwritable and read only optical disk cartridges using phase change - Capacity: 1,3 Gbytes per cartridge
  • ISO/IEC 14762:2009 Information technology - Functional safety requirements for Home and Building Electronic Systems (HBES)
  • ISO/IEC 14763 Information technology - Implementation and operation of customer premises cabling
    • ISO/IEC 14763-1:1999 Part 1: Administration
    • ISO/IEC 14763-2:2012 Part 2: Planning and installation
    • ISO/IEC TR 14763-2-1:2011 Part 2-1: Planning and installation - Identifiers within administration systems
    • ISO/IEC 14763-3:2014 Part 3: Testing of optical fibre cabling
  • ISO/IEC 14764:2006 Software Engineering - Software Life Cycle Processes - Maintenance
  • ISO/IEC 14765:1997 Information technology - Framework for protocol identification and encapsulation
  • ISO/IEC 14766:1997 Information technology - Telecommunications and information exchange between systems - Use of OSI applications over the Internet Transmission Control Protocol (TCP)
  • ISO/IEC 14769:2001 Information technology - Open Distributed Processing - Type Repository Function
  • ISO/IEC 14771:1999 Information technology - Open Distributed Processing - Naming framework
  • ISO/IEC 14772 Information technology - Computer graphics and image processing - The Virtual Reality Modeling Language (VRML)[Note 3]
    • ISO/IEC 14772-1:1997 Part 1: Functional specification and UTF-8 encoding
    • ISO/IEC 14772-2:2004 Part 2: External authoring interface (EAI)
  • ISO/IEC 14776 Information technology - Small Computer System Interface (SCSI)[Note 3]
    • ISO/IEC 14776-112:2002 Part 112: Parallel Interface-2 (SPI-2)
    • ISO/IEC 14776-113:2002 Part 113: Parallel Interface-3 (SPI-3)
    • ISO/IEC 14776-115:2004 Part 115: Parallel Interface-5 (SPI-5)
    • ISO/IEC 14776-121:2010 Part 121: Passive Interconnect Performance (PIP)
    • ISO/IEC 14776-150:2004 Part 150: Serial Attached SCSI (SAS)
    • ISO/IEC 14776-151:2010 Part 151: Serial Attached SCSI - 1.1 (SAS-1.1)
    • ISO/IEC 14776-153:2015 Part 153: Serial Attached SCSI - 2.1 (SAS-2.1)
    • ISO/IEC 14776-154:2017 Part 154: Serial Attached SCSI – 3 (SAS-3)
    • ISO/IEC 14776-222:2005 Part 222: Fibre Channel Protocol for SCSI, Second Version (FCP-2)
    • ISO/IEC 14776-223:2008 Part 223: Fibre Channel Protocol for SCSI, Third Version (FCP-3)
    • ISO/IEC 14776-232:2001 Part 232: Serial Bus Protocol 2 (SBP-2)
    • ISO/IEC 14776-251:2014 Part 251: USB attached SCSI (UAS)
    • ISO/IEC 14776-261:2012 Part 261: SAS Protocol Layer (SPL)
    • ISO/IEC 14776-262:2017 Part 262: SAS protocol layer - 2 (SPL-2)
    • ISO/IEC 14776-321:2002 Part 321: SCSI-3 Block Commands (SBC)
    • ISO/IEC 14776-322:2007 Part 322: SCSI Block Commands - 2 (SBC-2)
    • ISO/IEC 14776-323:2017 Part 323: SCSI Block commands - 3 (SBC-3)
    • ISO/IEC 14776-326:2015 Part 326: Reduced block commands (RBC)
    • ISO/IEC 14776-331:2002 Part 331: Stream Commands (SSC)
    • ISO/IEC 14776-333:2013 Part 333: SCSI Stream Commands - 3 (SSC-3)
    • ISO/IEC 14776-341:2000 Part 341: Controller Commands (SCC)
    • ISO/IEC 14776-342:2000 Part 342: Controller Commands - 2 (SCC-2)
    • ISO/IEC 14776-351:2007 Part 351: Medium Changer Commands (SCSI-3 SMC)
    • ISO/IEC 14776-362:2006 Part 362: Multimedia commands-2 (MMC-2)
    • ISO/IEC 14776-372:2011 Part 372: SCSI Enclosure Services - 2 (SES-2)
    • ISO/IEC 14776-381:2000 Part 381: Optical Memory Card Device Commands (OMC)
    • ISO/IEC 14776-411:1999 Part 411: SCSI-3 Architecture Model (SCSI-3 SAM)
    • ISO/IEC 14776-412:2006 Part 412: Architecture Model -2 (SAM-2)
    • ISO/IEC 14776-413:2007 Part 413: SCSI Architecture Model -3 (SAM-3)
    • ISO/IEC 14776-414:2009 Part 414: SCSI Architecture Model-4 (SAM-4)
    • ISO/IEC 14776-452:2005 Part 452: SCSI Primary Commands - 2 (SPC-2)
    • ISO/IEC 14776-453:2009 Part 453: Primary commands-3 (SPC-3)
  • ISO 14785:2014 Tourist information offices – Tourist information and reception services – Requirements
  • ISO/TR 14786:2014 Nanotechnologies – Considerations for the development of chemical nomenclature for selected nano-objects
  • ISO 14801 Dentistry – Implants – Dynamic fatigue test for endosseous dental implants
  • ISO/TR 14806:2013 Intelligent transport systems – Public transport requirements for the use of payment applications for fare media
  • ISO 14813 Intelligent transport systems – Reference model architecture(s) for the ITS sector
    • ISO 14813-1:2015 Part 1: ITS service domains, service groups and services
    • ISO 14813-5:2010 Part 5: Requirements for architecture description in ITS standards
    • ISO 14813-6:2009 Part 6: Data presentation in ASN.1
  • ISO 14814:2006 Road transport and traffic telematics – Automatic vehicle and equipment identification – Reference architecture and terminology
  • ISO 14815:2005 Road transport and traffic telematics – Automatic vehicle and equipment identification – System specifications
  • ISO 14816:2005 Road transport and traffic telematics – Automatic vehicle and equipment identification – Numbering and data structure
  • ISO 14817 Intelligent transport systems – ITS central data dictionaries
    • ISO 14817-1:2015 Part 1: Requirements for ITS data definitions
    • ISO 14817-2:2015 Part 2: Governance of the Central ITS Data Concept Registry
    • ISO 14817-3:2017 Part 3: Object identifier assignments for ITS data concepts
  • ISO 14819 Intelligent transport systems – Traffic and travel information messages via traffic message coding
    • ISO 14819-1:2013 Part 1: Coding protocol for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
    • ISO 14819-2:2013 Part 2: Event and information codes for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
    • ISO 14819-3:2013 Part 3: Location referencing for Radio Data System – Traffic Message Channel (RDS-TMC) using ALERT-C
    • ISO 14819-6:2006 Part 6: Encryption and conditional access for the Radio Data System – Traffic Message Channel ALERT C coding
  • ISO 14823:2017 Intelligent transport systems – Graphic data dictionary
  • ISO 14825:2011 Intelligent transport systems – Geographic Data Files (GDF) – GDF5.0
  • ISO 14827 Transport information and control systems – Data interfaces between centres for transport information and control systems
    • ISO 14827-1:2005 Part 1: Message definition requirements
    • ISO 14827-2:2005 Part 2: DATEX-ASN
  • ISO/IEC 14833:1996 Information technology – Data interchange on 12,7 mm 128-Track magnetic tape cartridges – DLT 3 format
  • ISO/IEC 14834:1996 Information technology - Distributed Transaction Processing - The XA Specification
  • ISO 14837 Mechanical vibration – Ground-borne noise and vibration arising from rail systems
    • ISO 14837-1:2005 Part 1: General guidance
    • ISO/TS 14837-31:2017 Part 31: Guideline on field measurements for the evaluation of human exposure in buildings
    • ISO/TS 14837-32:2015 Part 32: Measurement of dynamic properties of the ground
  • ISO 14839 Mechanical vibration - Vibration of rotating machinery equipped with active magnetic bearings
    • ISO 14839-1:2002 Part 1: Vocabulary
    • ISO 14839-2:2004 Part 2: Evaluation of vibration
    • ISO 14839-3:2006 Part 3: Evaluation of stability margin
    • ISO 14839-4:2012 Part 4: Technical guidelines
  • ISO/IEC 14840:1996 Information technology – 12,65 mm wide magnetic tape cartridge for information interchange – Helical scan recording – Data-D3-1 format
  • ISO/IEC 14841:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call offer supplementary service
  • ISO/IEC 14842:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Do not disturb and do not disturb override supplementary services
  • ISO/IEC 14843:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Offer supplementary service
  • ISO/IEC 14844:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Do Not Disturb and Do Not Disturb Override supplementary services
  • ISO/IEC 14845:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call intrusion supplementary service
  • ISO/IEC 14846:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Intrusion supplementary service
  • ISO 14855 Determination of the ultimate aerobic biodegradability of plastic materials under controlled composting conditions – Method by analysis of evolved carbon dioxide
    • ISO 14855-1:2012 General method
    • ISO 14855-2:2007 Gravimetric measurement of carbon dioxide evolved in a laboratory-scale test
  • ISO/IEC 14863:1996 Information technology - System-Independent Data Format (SIDF)
  • ISO/TR 14873:2013 Information and documentation - Statistics and quality issues for web archiving
  • ISO 14879 Implants for surgery – Total knee-joint prostheses
    • ISO 14879-1:2000 Part 1: Determination of endurance properties of knee tibial trays
  • ISO 14880 Optics and photonics - Microlens arrays
    • ISO 14880-1:2016 Part 1: Vocabulary and general properties
    • ISO 14880-2:2006 Part 2: Test methods for wavefront aberrations
    • ISO 14880-3:2006 Part 3: Test methods for optical properties other than wavefront aberrations
    • ISO 14880-4:2006 Part 4: Test methods for geometrical properties
    • ISO/TR 14880-5:2010 Part 5: Guidance on testing
  • ISO 14881:2001 Integrated optics – Interfaces – Parameters relevant to coupling properties
  • ISO/IEC 14882:2020 Programming languages — C++
  • ISO/IEC 14888 Information technology - Security techniques - Digital signatures with appendix
    • ISO/IEC 14888-1:2008 Part 1: General
    • ISO/IEC 14888-2:2008 Part 2: Integer factorization based mechanisms
    • ISO/IEC 14888-3:2016 Part 3: Discrete logarithm based mechanisms
  • ISO 14889:2013 Ophthalmic optics – Spectacle lenses – Fundamental requirements for uncut finished lenses
  • ISO/TS 14904:2002 Road transport and traffic telematics – Electronic fee collection (EFC) – Interface specification for clearing between operators
  • ISO 14906:2011 Electronic fee collection – Application interface definition for dedicated short-range communication
  • ISO/TS 14907 Electronic fee collection – Test procedures for user and fixed equipment
    • ISO/TS 14907-1:2015 Part 1: Description of test procedures
    • ISO/TS 14907-2:2016 Part 2: Conformance test for the on-board unit application interface
  • ISO/IEC 14908 Information technology - Control network protocol
    • ISO/IEC 14908-1:2012 Part 1: Protocol stack
    • ISO/IEC 14908-2:2012 Part 2: Twisted pair communication
    • ISO/IEC 14908-3:2012 Part 3: Power line channel specification
    • ISO/IEC 14908-4:2012 Part 4: IP communication
  • ISO 14915 Software ergonomics for multimedia user interfaces
    • ISO 14915-1:2002 Part 1: Design principles and framework
    • ISO 14915-2:2003 Part 2: Multimedia navigation and control
    • ISO 14915-3:2002 Part 3: Media selection and combination
  • ISO 14917:2017 Thermal spraying - Terminology, classification
  • ISO 14949:2001 Implants for surgery – Two-part addition-cure silicone elastomers
  • ISO 14963:2003 Mechanical vibration and shock – Guidelines for dynamic tests and investigations on bridges and viaducts
  • ISO 14971:2007 Medical devices – Application of risk management to medical devices
  • ISO 14972:1998 Sterile obturators for single use with over-needle peripheral intravascular catheters
  • ISO 14975:2000 Surface chemical analysis – Information formats
  • ISO 14976:1998 Surface chemical analysis – Data transfer format
  • ISO/IEC 14977:1996 Information technology – Syntactic metalanguage – Extended BNF
  • ISO 14978:2006 Geometrical product specifications (GPS) – General concepts and requirements for GPS measuring equipment
  • ISO 14982:1998 Agricultural and forestry machinery – Electromagnetic compatibility – Test methods and acceptance criteria

ISO 15000 – ISO 15999

  • ISO/TS 15000 Electronic business eXtensible Markup Language ebXML
    • ISO 15000-5:2014 Part 5: Core Components Specification (CCS)
  • ISO 15001:2010 Anaesthetic and respiratory equipment – Compatibility with oxygen
  • ISO 15002:2008 Flow-metering devices for connection to terminal units of medical gas pipeline systems
  • ISO 15004 Ophthalmic instruments – Fundamental requirements and test methods
    • ISO 15004-1:2006 Part 1: General requirements applicable to all ophthalmic instruments
    • ISO 15004-2:2007 Part 2: Light hazard protection
  • ISO 15006:2011 Road vehicles – Ergonomic aspects of transport information and control systems – Specifications for in-vehicle auditory presentation
  • ISO 15010:1998 Disposable hanging devices for transfusion and infusion bottles – Requirements and test methods
  • ISO 15016:2015 Ships and marine technology - Guidelines for the assessment of speed and power performance by analysis of speed trial data
  • ISO/IEC 15018:2004 Information technology - Generic cabling for homes
  • ISO 15022 Securities – Scheme for messages (Data Field Dictionary)
  • ISO/IEC 15026 Systems and software engineering—Systems and software assurance
    • ISO/IEC 15026-1:2013 Part 1: Concepts and vocabulary
    • ISO/IEC 15026-2:2011 Part 2: Assurance case
    • ISO/IEC 15026-3:2015 Part 3: System integrity levels
    • ISO/IEC 15026-4:2012 Part 4: Assurance in the life cycle
  • ISO 15031 Road vehicles – Communication between vehicle and external equipment for emissions-related diagnostics
    • ISO 15031-2:2010 Part 2: Guidance on terms, definitions, abbreviations and acronyms
  • ISO 15032:2000 Prostheses – Structural testing of hip units
  • ISO/IEC 15041:1997 Information technology - Data interchange on 90 mm optical disk cartridges - Capacity: 640 Mbytes per cartridge
  • ISO/IEC TR 15044:2000 Information technology - Terminology for the Home Electronic System (HES)
  • ISO/IEC 15045 Information technology - Home Electronic System (HES) gateway
    • ISO/IEC 15045-1:2004 Part 1: A residential gateway model for HES
    • ISO/IEC 15045-2:2012 Part 2: Modularity and protocol
  • ISO/IEC 15049:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Advice of charge supplementary services
  • ISO/IEC 15050:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Advice Of Charge supplementary services
  • ISO/IEC 15051:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Recall supplementary service
  • ISO/IEC 15052:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Recall supplementary service
  • ISO/IEC 15053:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call Interception additional network feature
  • ISO/IEC 15054:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Interception additional network feature
  • ISO/IEC 15055:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Transit counter additional network feature
  • ISO/IEC 15056:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Transit counter additional network feature
  • ISO/IEC 15067 Information technology - Home Electronic System (HES) application model[Note 4]
    • ISO/IEC TR 15067-2:1997 Part 2: Lighting model for HES
    • ISO/IEC 15067-3:2012 Part 3: Model of a demand-response energy management system for HES
    • ISO/IEC TR 15067-3-2:2016 Part 3-2: GridWise interoperability context-setting framework
    • ISO/IEC TR 15067-4:2001 Part 4: Security System for HES
  • ISO 15075:2003 Transport information and control systems – In-vehicle navigation systems – Communications message set requirements
  • ISO 15081:2011 Agricultural equipment - Graphical symbols for pressurized irrigation systems
  • ISO 15082 Road vehicles – Tests for rigid plastic safety glazing materials
  • ISO 15086 Hydraulic fluid power – Determination of the fluid-borne noise characteristics of components and systems
    • ISO 15086-1:2001 Part 1: Introduction
    • ISO 15086-2:2000 Part 2: Measurement of the speed of sound in a fluid in a pipe
    • ISO 15086-3:2008 Part 3: Measurement of hydraulic impedance
  • ISO 15099 Thermal performance of windows, doors and shading devices – Detailed calculations
  • ISO 15112 Natural gas – Energy determination
  • ISO 15118 Road vehicles - Vehicle to grid communication interface
  • ISO 15137:2005 Self-adhesive hanging devices for infusion bottles and injection vials – Requirements and test methods
  • ISO 15142 Implants for surgery – Metal intramedullary nailing systems
    • ISO 15142-1:2003 Part 1: Intramedullary nails
    • ISO 15142-2:2003 Part 2: Locking components
    • ISO 15142-3:2003 Part 3: Connection devices and reamer diameter measurements
  • ISO 15143 Earth-moving machinery and mobile road construction machinery – Worksite data exchange
    • ISO 15143-1:2010 Part 1: System architecture
    • ISO 15143-2:2010 Part 2: Data dictionary
    • ISO/TS 15143-3:2016 Part 3: Telematics data
  • ISO/IEC 15145:1997 Information technology - Programming languages - FORTH
  • ISO/IEC 15149:2011 Information technology – Telecommunications and information exchange between systems – Magnetic field area network (MFAN)
    • ISO/IEC 15149-1:2014 Part 1: Air interface
    • ISO/IEC 15149-2:2015 Part 2: In-band Control Protocol for Wireless Power Transfer
    • ISO/IEC 15149-3:2016 Part 3: Relay Protocol for Extended Range
    • ISO/IEC 15149-4:2016 Part 4: Security Protocol for Authentication
  • ISO 15174:2012 Milk and milk products – Microbial coagulants – Determination of total milk-clotting activity
  • ISO 15188:2001 Project management guidelines for terminology standardization
  • ISO 15189:2012 Medical laboratories – Particular requirements for quality and competence
  • ISO/IEC 15200:1996 Information technology - Adaptive Lossless Data Compression algorithm (ALDC)
  • ISO/IEC 15205:2000 SBus - Chip and module interconnect bus
  • ISO 15212 Oscillation-type density meters
    • ISO 15212-1:1998 Part 1: Laboratory instruments
    • ISO 15212-2:2002 Part 2: Process instruments for homogeneous liquids
  • ISO 15213:2003 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of sulfite-reducing bacteria growing under anaerobic conditions
  • ISO 15214:1998 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of mesophilic lactic acid bacteria – Colony-count technique at 30 degrees C
  • ISO 15216 Microbiology of the food chain - Horizontal method for determination of hepatitis A virus and norovirus using real-time RT-PCR[Note 4]
    • ISO 15216-1:2017 Part 1: Method for quantification
    • ISO/TS 15216-2:2013 Part 2: Method for qualitative detection
  • ISO 15223 Medical devices – Symbols to be used with medical device labels, labelling, and information to be supplied
    • ISO 15223-1:2016 Part 1: General requirements
    • ISO 15223-2:2010 Part 2: Symbol development, selection and validation
  • ISO 15225:2016 Medical devices – Quality management – Medical device nomenclature data structure
  • ISO 15226:1999 Technical product documentation – Life cycle model and allocation of documents
  • ISO 15230:2007 Mechanical vibration and shock – Coupling forces at the man–machine interface for hand-transmitted vibration
  • ISO/TR 15235:2001 Preparation of steel substrates before application of paints and related products - Collected information on the effect of levels of water-soluble salt contamination
  • ISO 15241:2012 Rolling bearings - Symbols for physical quantities
  • ISO 15253:2000 Ophthalmic optics and instruments – Optical devices for enhancing low vision
  • ISO 15254:2009 Ophthalmic optics and instruments – Electro-optical devices for enhancing low vision
  • ISO 15261:2004 Vibration and shock generating systems - Vocabulary
  • ISO/IEC TR 15285:1998 Information technology - An operational model for characters and glyphs
  • ISO/IEC 15286:1999 Information technology - 130 mm optical disk cartridges for information interchange - Capacity: 5,2 Gbytes per cartridge
  • ISO/IEC/IEEE 15288:2015 Systems and software engineering – System life cycle processes
  • ISO/IEC/IEEE 15289:2017 Systems and software engineering – Content of life-cycle information items (documentation)
  • ISO/IEC 15291:1999 Information technology – Programming languages – Ada Semantic Interface Specification (ASIS)
  • ISO/IEC TR 15294:2000 Information technology – Methods for data flow control at synchronous and asynchronous DTE-DCE interfaces
  • ISO 15296:2004 Gas welding equipment - Vocabulary - Terms used for gas welding equipment
  • ISO/TR 15300:2001 Dentistry - Application of OSI clinical codification to the classification and coding of dental products
  • ISO/IEC 15307:1997 Information technology – Data interchange on 12,7 mm 128-track magnetic tape cartridges – DLT 4 format
  • ISO 15309:2013 Implants for surgery – Differential scanning calorimetry of poly ether ether ketone (PEEK) polymers and compounds for use in implantable medical devices
  • ISO/PAS 15339 Graphic technology - Printing from digital data across multiple technologies
    • ISO/PAS 15339-1:2015 Part 1: Principles
    • ISO/PAS 15339-2:2015 Part 2: Characterized reference printing conditions, CRPC1-CRPC7
  • ISO 15367 Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront
    • ISO 15367-1:2003 Part 1: Terminology and fundamental aspects
    • ISO 15367-2:2005 Part 2: Shack-Hartmann sensors
  • ISO 15368:2001 Optics and optical instruments - Measurement of reflectance of plane surfaces and transmittance of plane parallel elements
  • ISO 15374:1998 Implants for surgery – Requirements for production of forgings
  • ISO 15375:2010 Medical infusion bottles – Suspension devices for multiple use – Requirements and test methods
  • ISO/TR 15377:2007 Measurement of fluid flow by means of pressure-differential devices – Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167
  • ISO 15378:2017 Primary packaging materials for medicinal products – Particular requirements for the application of ISO 9001:2015, with reference to good manufacturing practice (GMP)
  • ISO 15394:2009 Packaging - Bar code and two-dimensional symbols for shipping, transport and receiving labels
  • ISO 15403 Natural gas – Natural gas for use as a compressed fuel for vehicles
    • ISO 15403-1:2006 Part 1: Designation of the quality
    • ISO/TR 15403-2:2006 Part 2: Specification of the quality
  • ISO/IEC 15404:2000 Information technology – Office machines – Minimum information to be included in specification sheets – Facsimile equipment
  • ISO/IEC 15408 Information technology – Security techniques – Evaluation criteria for IT security
    • ISO/IEC 15408-1:2009 Part 1: Introduction and general model
    • ISO/IEC 15408-2:2008 Part 2: Security functional components
    • ISO/IEC 15408-3:2008 Part 3: Security assurance components
  • ISO/IEC TR 15410:1998 Information technology – Telecommunications and information exchange between systems – PISN mobility-general principles and services aspects
  • ISO/IEC 15411:1999 Information technology - Segmented keyboard layouts
  • ISO/IEC 15412:1999 Information technology - Portable computer keyboard layouts
  • ISO/IEC TR 15413:2001 Information technology - Font services - Abstract service definition
  • ISO/IEC 15414:2015 Information technology - Open data processing - Reference Model - Enterprise Language
  • ISO/IEC 15415:2011 Information technology - Automatic identification and data capture techniques - Bar code symbol print quality test specification - Two-dimensional symbols
  • ISO/IEC 15416:2016 Automatic identification and data capture techniques - Bar code print quality test specification - Linear symbols
  • ISO/IEC 15417:2007 Information technology - Automatic identification and data capture techniques - Code 128 bar code symbology specification
  • ISO/IEC 15418:2016 Information technology - Automatic identification and data capture techniques - GS1 Application Identifiers and ASC MH10 Data Identifiers and maintenance
  • ISO/IEC 15419:2009 Information technology - Automatic identification and data capture techniques - Bar code digital imaging and printing performance testing
  • ISO/IEC 15420:2009 Information technology - Automatic identification and data capture techniques - EAN/UPC bar code symbology specification
  • ISO/IEC 15421:2010 Information technology - Automatic identification and data capture techniques - Bar code master test specifications
  • ISO/IEC 15423:2009 Information technology - Automatic identification and data capture techniques - Bar code scanner and decoder performance testing
  • ISO/IEC 15424:2008 Information technology - Automatic identification and data capture techniques - Data Carrier Identifiers (including Symbology Identifiers)
  • ISO/IEC 15426 Information technology - Automatic identification and data capture techniques - Bar code verifier conformance specification
    • ISO/IEC 15426-1:2006 Part 1: Linear symbols
    • ISO/IEC 15426-2:2015 Part 2: Two-dimensional symbols
  • ISO/IEC 15428:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless Terminal Location Registration supplementary service and Wireless Terminal Information Exchange additional network feature
  • ISO/IEC 15429:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless Terminal Location Registration supplementary service and Wireless Terminal Information exchange additional network feature
  • ISO/IEC 15430:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless terminal call handling additional network features
  • ISO/IEC 15431:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless terminal call handling additional network features
  • ISO/IEC 15432:1999 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Wireless Terminal Authentication supplementary services (WTAT and WTAN)
  • ISO/IEC 15433:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Wireless Terminal Authentication supplementary services
  • ISO/IEC 15434:2006 Information technology – Automatic identification and data capture techniques – Syntax for high-capacity ADC media
  • ISO/IEC 15437:2001 Information technology - Enhancements to LOTOS (E-LOTOS)
  • ISO/IEC 15438:2015 Information technology - Automatic identification and data capture techniques - PDF417 bar code symbology specification
  • ISO/IEC TR 15440:2016 Information technology - Future keyboards and other input devices and entry methods
  • ISO/IEC TR 15443 Information technology - Security techniques - Security assurance framework
    • ISO/IEC TR 15443-1:2012 Part 1: Introduction and concepts
    • ISO/IEC TR 15443-2:2012 Part 2: Analysis
  • ISO/IEC 15444 Information technology – JPEG 2000 image coding system
    • ISO/IEC 15444-1:2016 Core coding system
    • ISO/IEC 15444-2:2004 Extensions
    • ISO/IEC 15444-3:2007 Motion JPEG 2000
    • ISO/IEC 15444-4:2004 Conformance testing
    • ISO/IEC 15444-5:2015 Reference software
    • ISO/IEC 15444-6:2013 Part 6: Compound image file format
    • ISO/IEC 15444-8:2007 Secure JPEG 2000
    • ISO/IEC 15444-9:2005 Interactivity tools, APIs and protocols
    • ISO/IEC 15444-10:2011 Extensions for three-dimensional data
    • ISO/IEC 15444-11:2007 Wireless
    • ISO/IEC 15444-12:2015 Part 12: ISO base media file format [Withdrawn, no replacement]
    • ISO/IEC 15444-13:2008 An entry level JPEG 2000 encoder
    • ISO/IEC 15444-14:2013 Part 14: XML representation and reference
  • ISO/IEC 15445:2000 Information technology – Document description and processing languages – HyperText Markup Language (HTML)
  • ISO/IEC TR 15446:2009 Information technology - Security techniques - Guide for the production of Protection Profiles and Security Targets
  • ISO/IEC 15457 Identification cards – Thin flexible cards
    • ISO/IEC 15457-1:2008 Part 1: Physical characteristics
    • ISO/IEC 15457-2:2007 Part 2: Magnetic recording technique
    • ISO/IEC 15457-3:2008 Part 3: Test methods
  • ISO/IEC 15459 Information technology - Automatic identification and data capture techniques - Unique identification
    • ISO/IEC 15459-1:2014 Part 1: Individual transport units
    • ISO/IEC 15459-2:2015 Part 2: Registration procedures
    • ISO/IEC 15459-3:2014 Part 3: Common rules
    • ISO/IEC 15459-4:2014 Part 4: Individual products and product packages
    • ISO/IEC 15459-5:2014 Part 5: Individual returnable transport items (RTIs)
    • ISO/IEC 15459-6:2014 Part 6: Groupings
  • ISO 15469:2004 Spatial distribution of daylight – CIE standard general sky
  • ISO/IEC 15474 Information technology - CDIF framework
    • ISO/IEC 15474-1:2002 Part 1: Overview
    • ISO/IEC 15474-2:2002 Part 2: Modelling and extensibility
  • ISO/IEC 15475 Information technology - CDIF transfer format
    • ISO/IEC 15475-1:2002 Part 1: General rules for syntaxes and encodings
    • ISO/IEC 15475-2:2002 Part 2: Syntax SYNTAX.1
    • ISO/IEC 15475-3:2002 Part 3: Encoding ENCODING.1
  • ISO/IEC 15476 Information technology - CDIF semantic metamodel
    • ISO/IEC 15476-1:2002 Part 1: Foundation
    • ISO/IEC 15476-2:2002 Part 2: Common
    • ISO/IEC 15476-3:2006 Part 3: Data definitions
    • ISO/IEC 15476-4:2005 Part 4: Data models
    • ISO/IEC 15476-6:2006 Part 6: State/event models
  • ISO 15480:2019 Fasteners — Hexagon washer head drilling screws with tapping screw thread
  • ISO 15481:1999 Cross recessed pan head drilling screws with tapping screw thread
  • ISO 15482:1999 Cross recessed countersunk head drilling screws with tapping screw thread
  • ISO 15483:1999 Cross recessed raised countersunk head drilling screws with tapping screw thread
  • ISO/IEC 15485:1997 Information technology - Data interchange on 120 mm optical disk cartridges using phase change PD format - Capacity: 650 Mbytes per cartridge
  • ISO/IEC 15486:1998 Information technology - Data interchange on 130 mm optical disk cartridges of type WORM (Write Once Read Many) using irreversible effects - Capacity: 2,6 Gbytes per cartridge
  • ISO 15489 Information and documentation – Records management
    • ISO 15489-1:2016 Part 1: Concepts and principles
    • ISO/TR 15489-2:2001 Part 2: Guidelines [Withdrawn, no replacement]
  • ISO/IEC 15498:1997 Information technology - Data interchange on 90 mm optical disk cartridges - HS-1 format - Capacity: 650 Mbytes per cartridge
  • ISO/IEC 15504 Information technology – Process assessment
  • ISO/IEC 15505:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Message Waiting Indication supplementary service
  • ISO/IEC 15506:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Message Waiting Indication supplementary service
  • ISO/IEC 15507:1997 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – PINX clock synchronization
  • ISO 15511:2011 Information and documentation - International standard identifier for libraries and related organizations (ISIL)
  • ISO 15519 Specification for diagrams for process industry
    • ISO 15519-1:2010 Part 1: General rules
    • ISO 15519-2:2015 Part 2: Measurement and control
  • ISO/IEC 15521:1998 Information technology – 3,81 mm wide magnetic tape cartridge for information interchange – Helical scan recording – DDS-3 format using 125 m length tapes
  • ISO 15529:2010 Optics and photonics - Optical transfer function - Principles of measurement of modulation transfer function (MTF) of sampled imaging systems
  • ISO 15530 Geometrical product specifications (GPS) – Coordinate measuring machines (CMM): Technique for determining the uncertainty of measurement
    • ISO/TS 15530-1:2013 Part 1: Overview and metrological characteristics
    • ISO 15530-3:2011 Part 3: Use of calibrated workpieces or measurement standards
    • ISO/TS 15530-4:2008 Part 4: Evaluating task-specific measurement uncertainty using simulation
  • ISO 15553:2006 Water quality – Isolation and identification of Cryptosporidium oocysts and Giardia cysts from water
  • ISO 15583:2005 Ships and marine technology - Maritime standards list
  • ISO/TR 15599:2002 Digital codification of dental laboratory procedures
  • ISO 15614 Specification and qualification of welding procedures for metallic materials – Welding procedure test
  • ISO 15622:2010 Intelligent transport systems – Adaptive Cruise Control systems – Performance requirements and test procedures
  • ISO 15623:2013 Intelligent transport systems – Forward vehicle collision warning systems – Performance requirements and test procedures
  • ISO/TS 15624:2001 Transport information and control systems – Traffic Impediment Warning Systems (TIWS) – System requirements
  • ISO 15628:2013 Intelligent transport systems – Dedicated short range communication (DSRC) – DSRC application layer
  • ISO 15638 Intelligent transport systems – Framework for cooperative telematics applications for regulated commercial freight vehicles (TARV)[Note 4]
    • ISO 15638-1:2012 Part 1: Framework and architecture
    • ISO 15638-2:2013 Part 2: Common platform parameters using CALM
    • ISO 15638-3:2013 Part 3: Operating requirements, 'Approval Authority' procedures, and enforcement provisions for the providers of regulated services
    • ISO 15638-5:2013 Part 5: Generic vehicle information
    • ISO 15638-6:2014 Part 6: Regulated applications
    • ISO 15638-7:2013 Part 7: Other applications
    • ISO 15638-8:2014 Part 8: Vehicle access management
    • ISO/TS 15638-9:2013 Part 9: Remote electronic tachograph monitoring (RTM)
    • ISO 15638-10:2017 Part 10: Emergency messaging system/eCall
    • ISO 15638-11:2014 Part 11: Driver work records
    • ISO 15638-12:2014 Part 12: Vehicle mass monitoring
    • ISO/TS 15638-13:2015 Part 13: "Mass" information for jurisdictional control and enforcement
    • ISO 15638-14:2014 Part 14: Vehicle access control
    • ISO 15638-15:2014 Part 15: Vehicle location monitoring
    • ISO 15638-16:2014 Part 16: Vehicle speed monitoring
    • ISO 15638-17:2014 Part 17: Consignment and location monitoring
    • ISO 15638-18:2017 Part 18: ADR (Dangerous Goods)
    • ISO/TS 15638-19:2013 Part 19: Vehicle parking facilities (VPF)
  • ISO 15642:2003 Road construction and maintenance equipment – Asphalt mixing plants – Terminology and commercial specifications
  • ISO 15662:2006 Intelligent transport systems – Wide area communication – Protocol management information
  • ISO 15664:2001 Acoustics – Noise control design procedures for open plant
  • ISO 15665:2003 Acoustics – Acoustic insulation for pipes, valves and flanges
  • ISO 15667:2000 Acoustics – Guidelines for noise control by enclosures and cabins
  • ISO 15674:2016 Cardiovascular implants and artificial organs – Hard-shell cardiotomy/venous reservoir systems (with/without filter) and soft venous reservoir bags
  • ISO 15675:2016 Cardiovascular implants and artificial organs – Cardiopulmonary bypass systems – Arterial blood line filters
  • ISO 15676:2016 Cardiovascular implants and artificial organs – Requirements for single-use tubing packs for cardiopulmonary bypass and extracorporeal membrane oxygenation (ECMO)
  • ISO 15686 Buildings and constructed assets – Service life planning
  • ISO 15688:2012 Road construction and maintenance equipment – Soil stabilizers – Terminology and commercial specifications
  • ISO 15689:2003 Road construction and maintenance equipment – Powder binder spreaders – Terminology and commercial specifications
  • ISO/IEC 15693 Identification cards – Contactless integrated circuit cards – Vicinity cards
  • ISO/TS 15696:2012 Cranes – List of equivalent terms
  • ISO 15706 Information and documentation – International Standard Audiovisual Number (ISAN)
  • ISO 15707:2001 Information and documentation – International Standard Musical Work Code (ISWC)
  • ISO/IEC 15718:1998 Information technology – Data interchange on 8 mm wide magnetic tape cartridge – Helical scan recording – HH-1 format
  • ISO/IEC 15731:1998 Information technology – 12,65 mm wide magnetic tape cassette for information interchange – Helical scan recording – DTF-1 format
  • ISO 15744:2002 Hand-held non-electric power tools – Noise measurement code – Engineering method (grade 2)
  • ISO 15747:2010 Plastic containers for intravenous injections
  • ISO 15752:2010 Ophthalmic instruments – Endoilluminators – Fundamental requirements and test methods for optical radiation safety
  • ISO/IEC 15757:1998 Information technology – Data interchange on 8 mm wide magnetic tape cartridge – Helical scan recording – DA-2 format
  • ISO 15759:2005 Medical infusion equipment – Plastics caps with inserted elastomeric liner for containers manufactured by the blow-fill-seal (BFS) process
  • ISO/TS 15768:2000 Measurement of liquid velocity in open channels – Design, selection and use of electromagnetic current meters
  • ISO 15769:2010 Hydrometry – Guidelines for the application of acoustic velocity meters using the Doppler and echo correlation methods
  • ISO/IEC 15771:1998 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Common information additional network feature
  • ISO/IEC 15772:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Common Information additional network feature
  • ISO/IEC 15773:1998 Information technology – Telecommunications and information exchange between systems – Broadband Private Integrated Services Network – Inter-exchange signalling protocol – Transit counter additional network feature
  • ISO/IEC 15776:2001 VME64bus - Specification
  • ISO/IEC 15780:1998 Information technology – 8 mm wide magnetic tape cartridge – Helical scan recording – AIT-1 format
  • ISO 15782 Certificate management for financial services[Note 4]
    • ISO 15782-1:2009 Part 1: Public key certificates
    • ISO 15782-2:2001 Part 2: Certificate extensions
  • ISO 15783:2002 Seal-less rotodynamic pumps – Class II – Specification
  • ISO 15784 Intelligent transport systems (ITS) – Data exchange involving roadside modules communication
    • ISO 15784-1:2008 Part 1: General principles and documentation framework of application profiles
    • ISO 15784-2:2015 Part 2: Centre to field device communications using SNMP
    • ISO 15784-3:2008 Part 3: Application profile-data exchange (AP-DATEX)
  • ISO 15785:2002 Technical drawings – Symbolic presentation and indication of adhesive, fold and pressed joints
  • ISO 15786:2008 Technical drawings – Simplified representation and dimensioning of holes
  • ISO 15787:2016 Technical product documentation – Heat-treated ferrous parts – Presentation and indications
  • ISO 15798:2013 Ophthalmic implants – Ophthalmic viscosurgical devices
  • ISO/IEC 15802 Information technology – Telecommunications and information exchange between systems – Local and metropolitan area networks – Common specifications
    • ISO/IEC 15802-1:1995 Part 1: Medium Access Control (MAC) service definition
    • ISO/IEC 15802-3:1998 Part 3: Media Access Control (MAC) Bridges
  • ISO/IEC 15816:2002 Information technology - Security techniques - Security information objects for access control
  • ISO 15836:2009 Information and documentation – The Dublin Core metadata element set
    • ISO 15836-1:2017 Part 1: Core elements
  • ISO/TR 15847:2008 Graphic technology - Graphical symbols for printing press systems and finishing systems, including related auxiliary equipment
  • ISO 15849:2001 Ships and marine technology – Guidelines for implementation of a fleet management system network
  • ISO/IEC 15851:1999 Information technology - Communication protocol - Open MUMPS Interconnect
  • ISO/IEC 15852:1999 Information technology - Programming languages - M Windowing API
  • ISO 15867:2003 Intermediate bulk containers (IBCs) for non-dangerous goods – Terminology
  • ISO 15870:2000 Powered industrial trucks - Safety signs and hazard pictorials - General principles
  • ISO 15878:2008 Road construction and maintenance equipment – Asphalt pavers – Terminology and commercial specifications
  • ISO/IEC 15895:1999 Information technology – Data interchange on 12,7 mm 128-track magnetic tape cartridges – DLT 3-XT format
  • ISO/IEC 15896:1999 Information technology – Data interchange on 12,7 mm 208-track magnetic tape cartridges – DLT 5 format
  • ISO/IEC 15897:2011 Information technology - User interfaces - Procedures for the registration of cultural elements
  • ISO 15883-1:2006 specifies general performance requirements for washer-disinfectors (WD) and their accessories that are intended to be used for cleaning and disinfection of re-usable medical devices and other articles used in the context of medical, dental, pharmaceutical and veterinary practice.
  • ISO/IEC 15898:1998 Information technology - Data interchange on 356 mm optical disk cartridges - WORM, using phase change technology - Capacity: 14,8 Gbytes and 25 Gbytes per cartridge
  • ISO/IEC 15899:1998 Information technology – Telecommunications and information exchange between systems – Broadband Private Integrated Services Network – Service description – Broadband connection oriented bearer services
  • ISO 15901-2:2022 Pore size distribution and porosity of solid materials by mercury porosimetry and gas adsorption — Part 2: Analysis of nanopores by gas adsorption
  • ISO 15902:2004 Optics and photonics - Diffractive optics - Vocabulary
  • ISO/IEC 15909 Systems and software engineering - High-level Petri nets
    • ISO/IEC 15909-1:2004 Part 1: Concepts, definitions and graphical notation
    • ISO/IEC 15909-2:2011 Part 2: Transfer format
  • ISO 15919:2001 Information and documentation - Transliteration of Devanagari and related Indic scripts into Latin characters
  • ISO 15924:2004 Information and documentation – Codes for the representation of names of scripts
  • ISO 15926 - Integration of Life-cycle Data for Process Plants including Oil and Gas Production Facilities
  • ISO 15927 Hygrothermal performance of buildings – Calculation and presentation of climatic data
    • ISO 15927-1:2003 Part 1: Monthly means of single meteorological elements
    • ISO 15927-2:2009 Part 2: Hourly data for design cooling load
    • ISO 15927-3:2009 Part 3: Calculation of a driving rain index for vertical surfaces from hourly wind and rain data
    • ISO 15927-4:2005 Part 4: Hourly data for assessing the annual energy use for heating and cooling
    • ISO 15927-5:2004 Part 5: Data for design heat load for space heating
    • ISO 15927-6:2007 Part 6: Accumulated temperature differences (degree-days)
  • ISO 15930 Graphic technology – Prepress digital data exchange using PDF[Note 4]
  • ISO 15932:2013 Microbeam analysis - Analytical electron microscopy - Vocabulary
  • ISO/IEC 15938 Information technology - Multimedia content description interface
  • ISO/IEC/IEEE 15939:2017 Systems and software engineering - Measurement process
  • ISO/IEC 15940:2013 Systems and software engineering - Software Engineering Environment Services
  • ISO/IEC TR 15942:2000 Information technology - Programming languages - Guide for the use of the Ada programming language in high integrity systems
  • ISO/IEC 15944 Information technology - Business operational view
    • ISO/IEC 15944-1:2011 Part 1: Operational aspects of open-edi for implementation
    • ISO/IEC 15944-2:2015 Part 2: Registration of scenarios and their components as business objects
    • ISO/IEC 15944-4:2015 Part 4: Business transaction scenarios – Accounting and economic ontology
    • ISO/IEC 15944-5:2008 Part 5: Identification and referencing of requirements of jurisdictional domains as sources of external constraints
    • ISO/IEC TR 15944-6:2015 Part 6: Technical introduction to e-Business modelling
    • ISO/IEC 15944-7:2009 Part 7: eBusiness vocabulary
    • ISO/IEC 15944-8:2012 Part 8: Identification of privacy protection requirements as external constraints on business transactions
    • ISO/IEC 15944-9:2015 Part 9: Business transaction traceability framework for commitment exchange
    • ISO/IEC 15944-10:2013 Part 10: IT-enabled coded domains as semantic components in business transactions
    • ISO/IEC 15944-20:2015 Part 20: Linking business operational view to functional service view
  • ISO/IEC 15945:2002 Information technology - Security techniques - Specification of TTP services to support the application of digital signatures
  • ISO/IEC 15946 Information technology - Security techniques - Cryptographic techniques based on elliptic curves
    • ISO/IEC 15946-1:2016 Part 1: General
    • ISO/IEC 15946-5:2017 Part 5: Elliptic curve generation
  • ISO/IEC 15948 Information technology – Computer graphics and image processing – Portable Network Graphics (PNG): Functional specification
  • ISO/IEC 15953:1999 Information technology – Open Systems Interconnection – Service definition for the Application Service Object Association Control Service Element
  • ISO/IEC 15954:1999 Information technology – Open Systems Interconnection – Connection-mode protocol for the Application Service Object Association Control Service Element
  • ISO/IEC 15955:1999 Information technology – Open Systems Interconnection – Connectionless protocol for the Application Service Object Association Control Service Element
  • ISO/IEC 15961 Information technology - Radio frequency identification (RFID) for item management: Data protocol
    • ISO/IEC 15961-1:2013 Part 1: Application interface
    • ISO/IEC 15961-4:2016 Part 4: Application interface commands for battery assist and sensor functionality
  • ISO/IEC 15962:2013 Information technology - Radio frequency identification (RFID) for item management - Data protocol: data encoding rules and logical memory functions
  • ISO/IEC 15963:2009 Information technology - Radio frequency identification for item management - Unique identification for RF tags
  • ISO 15970 Natural gas – Measurement of properties – Volumetric properties: density, pressure, temperature and compression factor
  • ISO 15971:2008 Natural gas – Measurement of properties – Calorific value and Wobbe index
  • ISO 15985:2004 Plastics – Determination of the ultimate anaerobic biodegradation and disintegration under high-solids anaerobic-digestion conditions – Method by analysis of released biogas
  • ISO/IEC 15991:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Specification, functional model and information flows – Call Priority Interruption and Call Priority Interruption Protection supplementary services
  • ISO/IEC 15992:2003 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Inter-exchange signalling protocol – Call Priority Interruption and Call Priority Interruption Protection supplementary services

Notes

  1. ↑ This list generally excludes draft versions.
  2. ↑ ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards".
  3. ↑ 3.0 3.1 3.2 The exact wording of this title varies between parts. This is the wording of the most recently published part.
  4. ↑ 4.0 4.1 4.2 4.3 4.4 The exact wording of this title varies between parts. This is the wording of the most recently published part.

References

  1. ↑ "Standards catalogue". ISO. https://www.iso.org/standards-catalogue/browse-by-ics.html. 
  2. ↑ "Freely Available Standards". ISO. http://standards.iso.org/ittf/PubliclyAvailableStandards/index.html. 
  3. ↑ European Standards, ISO 14045, accessed 2 August 2023

External links



Retrieved from "https://handwiki.org/wiki/index.php?title=List_of_ISO_standards_14000–15999&oldid=3364342"