Physics:Ampère's force law

Short description: Physical law

Two current-carrying wires attract each other magnetically: The bottom wire has current I₁, which creates magnetic field B₁. The top wire carries a current I₂ through the magnetic field B₁, so (by the Lorentz force) the wire experiences a force F₁₂. (Not shown is the simultaneous process where the top wire makes a magnetic field which results in a force on the bottom wire.)

In magnetostatics, the force of attraction or repulsion between two current-carrying wires (see first figure below) is often called Ampère's force law. The physical origin of this force is that each wire generates a magnetic field, following the Biot–Savart law, and the other wire experiences a magnetic force as a consequence, following the Lorentz force law.

Equation

Special case: Two straight parallel wires

The best-known and simplest example of Ampère's force law, which underlaid (before 20 May 2019) the definition of the ampere, the SI unit of electric current, states that the magnetic force per unit length between two straight parallel conductors is

[math]\displaystyle{ \frac {F_m} {L} = 2 k_{\rm A} \frac {I_1 I_2 } {r}, }[/math]

where [math]\displaystyle{ k_{\rm A} }[/math] is the magnetic force constant from the Biot–Savart law, [math]\displaystyle{ F_m / L }[/math] is the total force on either wire per unit length of the shorter (the longer is approximated as infinitely long relative to the shorter), [math]\displaystyle{ r }[/math] is the distance between the two wires, and [math]\displaystyle{ I_1 }[/math], [math]\displaystyle{ I_2 }[/math] are the direct currents carried by the wires.

This is a good approximation if one wire is sufficiently longer than the other, so that it can be approximated as infinitely long, and if the distance between the wires is small compared to their lengths (so that the one infinite-wire approximation holds), but large compared to their diameters (so that they may also be approximated as infinitely thin lines). The value of [math]\displaystyle{ k_{\rm A} }[/math] depends upon the system of units chosen, and the value of [math]\displaystyle{ k_{\rm A} }[/math] decides how large the unit of current will be.

In the SI system, [math]\displaystyle{ k_{\rm A} \ \overset{\underset{\mathrm{def}}{}}{=}\ \frac {\mu_0}{ 4\pi} }[/math] with [math]\displaystyle{ \mu_0 }[/math] the magnetic constant, in SI units

μ₀ = 1.25663706212(19)×10⁻⁶ H/m

General case

The general formulation of the magnetic force for arbitrary geometries is based on iterated line integrals and combines the Biot–Savart law and Lorentz force in one equation as shown below.

[math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0} {4 \pi} \int_{L_1} \int_{L_2} \frac {I_1 d \boldsymbol{\ell}_1\ \times \ (I_2 d \boldsymbol{\ell}_2 \ \times \ \hat{\mathbf{r}}_{21} )} {|r|^2}, }[/math]

where

• [math]\displaystyle{ \mathbf{F}_{12} }[/math] is the total magnetic force felt by wire 1 due to wire 2 (usually measured in newtons),
• [math]\displaystyle{ I_1 }[/math] and [math]\displaystyle{ I_2 }[/math] are the currents running through wires 1 and 2, respectively (usually measured in amperes),
• The double line integration sums the force upon each element of wire 1 due to the magnetic field of each element of wire 2,
• [math]\displaystyle{ d \boldsymbol{\ell}_1 }[/math] and [math]\displaystyle{ d \boldsymbol{\ell}_2 }[/math] are infinitesimal vectors associated with wire 1 and wire 2 respectively (usually measured in metres); see line integral for a detailed definition,
• The vector [math]\displaystyle{ \hat{\mathbf{r}}_{21} }[/math] is the unit vector pointing from the differential element on wire 2 towards the differential element on wire 1, and |r| is the distance separating these elements,
• The multiplication × is a vector cross product,
• The sign of [math]\displaystyle{ I_n }[/math] is relative to the orientation [math]\displaystyle{ d \boldsymbol{\ell}_n }[/math] (for example, if [math]\displaystyle{ d \boldsymbol{\ell}_1 }[/math] points in the direction of conventional current, then [math]\displaystyle{ I_1 \gt 0 }[/math]).

To determine the force between wires in a material medium, the magnetic constant is replaced by the actual permeability of the medium.

For the case of two separate closed wires, the law can be rewritten in the following equivalent way by expanding the vector triple product and applying Stokes' theorem: [math]\displaystyle{ \mathbf{F}_{12} = -\frac {\mu_0} {4 \pi} \int_{L_1} \int_{L_2} \frac {( I_1 d \boldsymbol{\ell}_1\ \mathbf{ \cdot} \ I_2 d \boldsymbol{\ell}_2 ) \ \hat{\mathbf{r}}_{21} } {|r|^2}. }[/math]

In this form, it is immediately obvious that the force on wire 1 due to wire 2 is equal and opposite the force on wire 2 due to wire 1, in accordance with Newton's third law of motion.

Historical background

Diagram of original Ampere experiment

The form of Ampere's force law commonly given was derived by James Clerk Maxwell in 1873 and is one of several expressions consistent with the original experiments of André-Marie Ampère and Carl Friedrich Gauss. The x-component of the force between two linear currents I and I', as depicted in the adjacent diagram, was given by Ampère in 1825 and Gauss in 1833 as follows:

[math]\displaystyle{ dF_x = k I I' ds' \int ds \frac {\cos(xds) \cos(rds') - \cos(rx)\cos(dsds')} {r^2}. }[/math]

Following Ampère, a number of scientists, including Wilhelm Weber, Rudolf Clausius, Maxwell, Bernhard Riemann, Hermann Grassmann, and Walther Ritz, developed this expression to find a fundamental expression of the force. Through differentiation, it can be shown that:

[math]\displaystyle{ \frac{\cos(x\,ds) \cos(r\,ds')} {r^2} = -\cos(rx) \frac{(\cos\varepsilon - 3 \cos\phi \cos\phi')} {r^2}. }[/math]

and also the identity: [math]\displaystyle{ \frac{\cos(rx) \cos(ds\,ds')} {r^2} = \frac{\cos(rx) \cos\varepsilon} {r^2} . }[/math]

With these expressions, Ampère's force law can be expressed as: [math]\displaystyle{ dF_x = k I I' ds' \int ds' \cos(rx) \frac{2\cos\varepsilon - 3\cos\phi \cos\phi'} {r^2} . }[/math]

Using the identities: [math]\displaystyle{ \frac{\partial r} {\partial s} = \cos\phi, \frac{\partial r} {\partial s'} = -\cos\phi' . }[/math] and [math]\displaystyle{ \frac{\partial^2 r} {\partial s \partial s'} = \frac{-\cos\varepsilon + \cos\phi \cos\phi'} {r} . }[/math]

Ampère's results can be expressed in the form: [math]\displaystyle{ d^2 F = \frac{k I I' ds ds'} {r^2} \left( \frac{\partial r}{\partial s} \frac{\partial r}{\partial s'} - 2r \frac{\partial^2 r}{\partial s \partial s'}\right). }[/math]

As Maxwell noted, terms can be added to this expression, which are derivatives of a function Q(r) and, when integrated, cancel each other out. Thus, Maxwell gave "the most general form consistent with the experimental facts" for the force on ds arising from the action of ds': [math]\displaystyle{ d^2 F_x = k I I' ds ds'\frac{1} {r^2} \left[ \left( \left( \frac{\partial r}{\partial s} \frac{\partial r}{\partial s'} - 2r \frac{\partial^2 r}{\partial s \partial s'}\right) + r \frac{\partial^2 Q}{\partial s \partial s'}\right) \cos(rx) + \frac{\partial Q} {\partial s'} \cos(x\,ds) - \frac{\partial Q} {\partial s} \cos(x\,ds') \right] . }[/math]

Q is a function of r, according to Maxwell, which "cannot be determined, without assumptions of some kind, from experiments in which the active current forms a closed circuit." Taking the function Q(r) to be of the form: [math]\displaystyle{ Q = - \frac{(1+k)} {2r} }[/math]

We obtain the general expression for the force exerted on ds by ds: [math]\displaystyle{ d^2\mathbf{F} = -\frac{k I I'} {2r^2} \left[ \left(3-k\right) \hat{\mathbf{r}}_1 \left(d\mathbf{s}\,d\mathbf{s}'\right) - 3\left(1-k\right) \hat{\mathbf{r}}_1 \left(\mathbf{\hat{r}}_1 d\mathbf{s}\right) \left(\mathbf{\hat{r}}_1 d\mathbf{s}'\right) - \left(1+k\right) d\mathbf{s} \left(\mathbf{\hat{r}}_1 d\mathbf{s}'\right) - \left(1+k\right) d\mathbf{s}' \left(\mathbf{\hat{r}}_1 d\mathbf{s}\right) \right] . }[/math]

Integrating around s' eliminates k and the original expression given by Ampère and Gauss is obtained. Thus, as far as the original Ampère experiments are concerned, the value of k has no significance. Ampère took k=−1; Gauss took k=+1, as did Grassmann and Clausius, although Clausius omitted the S component. In the non-ethereal electron theories, Weber took k=−1 and Riemann took k=+1. Ritz left k undetermined in his theory. If we take k = −1, we obtain the Ampère expression: [math]\displaystyle{ d^2\mathbf{F} = -\frac{k I I'} {r^3} \left[ 2 \mathbf{r} (d\mathbf{s} \, d\mathbf{s'}) - 3\mathbf{r} (\mathbf{r} d\mathbf{s}) (\mathbf{r} d\mathbf{s'}) \right] }[/math]

If we take k=+1, we obtain [math]\displaystyle{ d^2\mathbf{F} = -\frac{k I I'} {r^3} \left[ \mathbf{r} \left(d\mathbf{s} \, d\mathbf{s'}\right) - d\mathbf{s} \left(\mathbf{r} \, d\mathbf{s}'\right) - d\mathbf{s}'\left(\mathbf{r} \, d\mathbf{s}\right) \right] }[/math]

Using the vector identity for the triple cross product, we may express this result as [math]\displaystyle{ d^2\mathbf{F} = \frac{k I I'} {r^3} \left[ \left(d\mathbf{s} \times d\mathbf{s'}\times\mathbf{r}\right) + d\mathbf{s}'(\mathbf{r} \, d\mathbf{s}) \right] }[/math]

When integrated around ds' the second term is zero, and thus we find the form of Ampère's force law given by Maxwell: [math]\displaystyle{ \mathbf{F} = k I I' \iint \frac{d\mathbf{s} \times (d\mathbf{s}' \times \mathbf{r})} {|r|^3} }[/math]

Derivation of parallel straight wire case from general formula

Start from the general formula: [math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0} {4 \pi} \int_{L_1} \int_{L_2} \frac {I_1 d \boldsymbol{\ell}_1\ \times \ (I_2 d \boldsymbol{\ell}_2 \ \times \ \hat{\mathbf{r}}_{21} )} {|r|^2}, }[/math] Assume wire 2 is along the x-axis, and wire 1 is at y=D, z=0, parallel to the x-axis. Let [math]\displaystyle{ x_1,x_2 }[/math] be the x-coordinate of the differential element of wire 1 and wire 2, respectively. In other words, the differential element of wire 1 is at [math]\displaystyle{ (x_1,D,0) }[/math] and the differential element of wire 2 is at [math]\displaystyle{ (x_2,0,0) }[/math]. By properties of line integrals, [math]\displaystyle{ d\boldsymbol{\ell}_1=(dx_1,0,0) }[/math] and [math]\displaystyle{ d\boldsymbol{\ell}_2=(dx_2,0,0) }[/math]. Also, [math]\displaystyle{ \hat{\mathbf{r}}_{21} = \frac{1}{\sqrt{(x_1-x_2)^2+D^2}}(x_1-x_2,D,0) }[/math] and [math]\displaystyle{ |r| = \sqrt{(x_1-x_2)^2+D^2} }[/math] Therefore, the integral is [math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0 I_1 I_2} {4 \pi} \int_{L_1} \int_{L_2} \frac {(dx_1,0,0)\ \times \ \left[ (dx_2,0,0) \ \times \ (x_1-x_2,D,0) \right ] } {|(x_1-x_2)^2+D^2|^{3/2}}. }[/math] Evaluating the cross-product: [math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0 I_1 I_2} {4 \pi} \int_{L_1} \int_{L_2} dx_1 dx_2 \frac {(0,-D,0)} {|(x_1-x_2)^2+D^2|^{3/2}}. }[/math] Next, we integrate [math]\displaystyle{ x_2 }[/math] from [math]\displaystyle{ -\infty }[/math] to [math]\displaystyle{ +\infty }[/math]: [math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0 I_1 I_2} {4 \pi}\frac{2}{D}(0,-1,0) \int_{L_1} dx_1 . }[/math] If wire 1 is also infinite, the integral diverges, because the total attractive force between two infinite parallel wires is infinity. In fact, what we really want to know is the attractive force per unit length of wire 1. Therefore, assume wire 1 has a large but finite length [math]\displaystyle{ L_1 }[/math]. Then the force vector felt by wire 1 is: [math]\displaystyle{ \mathbf{F}_{12} = \frac {\mu_0 I_1 I_2} {4 \pi}\frac{2}{D}(0,-1,0) L_1 . }[/math] As expected, the force that the wire feels is proportional to its length. The force per unit length is: [math]\displaystyle{ \frac{\mathbf{F}_{12}}{L_1} = \frac {\mu_0 I_1 I_2} {2 \pi D}(0,-1,0) . }[/math] The direction of the force is along the y-axis, representing wire 1 getting pulled towards wire 2 if the currents are parallel, as expected. The magnitude of the force per unit length agrees with the expression for [math]\displaystyle{ \frac {F_m} {L} }[/math] shown above.

Notable derivations

Chronologically ordered:

• Ampère's original 1823 derivation:
  • Assis, André Koch Torres; Chaib, J. P. M. C; Ampère, André-Marie (2015). Ampère's electrodynamics: analysis of the meaning and evolution of Ampère's force between current elements, together with a complete translation of his masterpiece: Theory of electrodynamic phenomena, uniquely deduced from experience. Montreal: Apeiron. ISBN 978-1-987980-03-5. http://www.ifi.unicamp.br/~assis/Amperes-Electrodynamics.pdf. 
• Maxwell's 1873 derivation:
  • Treatise on Electricity and Magnetism vol. 2, part 4, ch. 2 (§§502–527)
• Pierre Duhem's 1892 derivation:
  • Duhem, Pierre Maurice Marie (2018-09-09). Ampère's Force Law: A Modern Introduction. Alan Aversa (trans.). doi:10.13140/RG.2.2.31100.03206/1. https://isidore.co/calibre/get/PDF/6855. Retrieved 2019-07-03.  (EPUB)
    • translation of: Leçons sur l'électricité et le magnétisme vol. 3, appendix to book 14, pp. 309-332 (in French)
• Alfred O'Rahilly's 1938 derivation:
  • Electromagnetic Theory: A Critical Examination of Fundamentals vol. 1, pp. 102–104 (cf. the following pages, too)

See also

• Ampere
• Magnetic constant
• Lorentz force
• Ampère's circuital law
• Free space

External links

• Ampère's force law Includes animated graphic of the force vectors.