Chemistry:Butanone

From HandWiki
Butanone[1]
Skeletal formula of butanone
Ball-and-stick model of butanone
Space-filling model of butanone
methyl ethyl ketone
Names
Preferred IUPAC name
Butan-2-one[2]
Other names
  • 2-Butanone
  • Ethyl methyl ketone[2]
  • Ethylmethylketone
  • Methyl ethyl ketone (MEK; deprecated[2])
  • Methylpropanone
  • Methylacetone
Identifiers
3D model (JSmol)
741880
ChEBI
ChEMBL
ChemSpider
25656
KEGG
RTECS number
  • EL6475000
UNII
Properties
C4H8O
Molar mass 72.107 g·mol−1
Appearance Colorless liquid
Odor Mint or acetone-like[3]
Density 0.8050 g/mL
Melting point −86 °C (−123 °F; 187 K)
Boiling point 79.64 °C (175.35 °F; 352.79 K)
27.5 g/100 mL
log P 0.37[4]
Vapor pressure 78 mmHg (20 °C)[3]
Acidity (pKa) 14.7
−45.58·10−6 cm3/mol
1.37880
Viscosity 0.43 cP
Structure
2.76 D
Hazards
Safety data sheet Safety Data Sheet
GHS pictograms GHS02: FlammableGHS07: Harmful[5]
GHS Signal word Danger[5]
H225, H319, H336[5]
P233, P210, P280, P240, P241, P243, P242, P264, P261, P271, P370+378, P303+361+353, P305+351+338, P337+313, P304+340, P312, P403+235, P501, P403+233, P405[5]
NFPA 704 (fire diamond)
Flammability code 3: Liquids and solids that can be ignited under almost all ambient temperature conditions. Flash point between 23 and 38 °C (73 and 100 °F). E.g. gasolineHealth code 1: Exposure would cause irritation but only minor residual injury. E.g. turpentineReactivity code 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g. liquid nitrogenSpecial hazards (white): no codeNFPA 704 four-colored diamond
3
1
0
Flash point −9 °C (16 °F; 264 K)
505 °C (941 °F; 778 K)
Explosive limits 1.4–11.4%[3]
Lethal dose or concentration (LD, LC):
  • 2737 mg/kg (oral, rat)
  • 4050 mg/kg (oral, mouse)[6]
  • 12667 ppm (mammal)
  • 13333 ppm (mouse, 2 hr)
  • 7833 ppm (rat, 8 hr)[6]
NIOSH (US health exposure limits):
PEL (Permissible)
 TWA 200 ppm (590 mg/m3)[3]
REL (Recommended)
 TWA 200 ppm (590 mg/m3) ST 300 ppm (885 mg/m3)[3]
IDLH (Immediate danger)
 3000 ppm[3]
Related compounds
Related ketones
 Acetone; 3-pentanone; 3-methylbutanone
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
☑Y verify (what is ☑Y☒N ?)
Infobox references
Tracking categories (test):

Butanone, also known as methyl ethyl ketone (MEK) or ethyl methyl ketone,[lower-alpha 1] is an organic compound with the formula CH3C(O)CH2CH3. This colorless liquid ketone has a sharp, sweet odor reminiscent of acetone. It is produced industrially on a large scale, but occurs in nature only in trace amounts.[7] It is partially soluble in water, and is commonly used as an industrial solvent.[8] It is an isomer of another solvent, tetrahydrofuran.

Production

Butanonyl may be produced by oxidation of 2-butanol. The dehydrogenation of 2-butanol is catalysed by copper, zinc, or bronze:

CH3CH(OH)CH2CH3 → CH3C(O)CH2CH3 + H2

This is used to produce approximately 700 million kilograms yearly. Other syntheses that have been examined but not implemented include Wacker oxidation of 2-butene and oxidation of isobutylbenzene, which is analogous to the industrial production of acetone.[7] The cumene process can be modified to produce phenol and a mixture of acetone and butanone instead of only phenol and acetone in the original.[9]

Both liquid-phase oxidation of heavy naphtha and the Fischer–Tropsch reaction produce mixed oxygenate streams, from which 2-butanone is extracted by fractionation.[10]

Applications

Solvent

Butanone is an effective and common solvent[8] and is used in processes involving gums, resins, cellulose acetate and nitrocellulose coatings and in vinyl films.[11] For this reason it finds use in the manufacture of plastics, textiles, in the production of paraffin wax, and in household products such as lacquer, varnishes, paint remover, a denaturing agent for denatured alcohol, glues, and as a cleaning agent. It has similar solvent properties to acetone but boils at a higher temperature and has a significantly slower evaporation rate.[12] Unlike acetone, it forms an azeotrope with water,[13][14] making it useful for azeotropic distillation of moisture in certain applications. Butanone is also used in dry erase markers as the solvent of the erasable dye.

Plastic welding

As butanone dissolves polystyrene and many other plastics, it is sold as "model cement" for use in connecting parts of scale model kits. Though often considered an adhesive, it is functioning as a welding agent in this context.

Other uses

Butanone is the precursor to methyl ethyl ketone peroxide, which is a catalyst for some polymerization reactions such as crosslinking of unsaturated polyester resins. Dimethylglyoxime can be prepared from butanone first by reaction with ethyl nitrite to give diacetyl monoxime followed by conversion to the dioxime:[15]

Preparation of dimethylglyoxime.png

In the peroxide process on producing hydrazine, the starting chemical ammonia is bonded to butanone, oxidized by hydrogen peroxide, bonded to another ammonia molecule.

Pechiney-Ugine-Kuhlmann process.png

In the final step of the process, hydrolysis produces the desired product, hydrazine, and regenerates the butanone.

Me(Et)C=NN=C(Et)Me + 2 H2O → 2 Me(Et)C=O + N2H4

Safety

Flammability

Butanone can react with most oxidizing materials and can produce fires.[8] It is moderately explosive, requiring only a small flame or spark to cause a vigorous reaction.[8] The vapor is heavier than air, so it can accumulate at low points. It is explosive at concentrations between 1.4 and 11.4%.[16] Concentrations in the air high enough to be flammable are intolerable to humans due to the irritating nature of the vapor.[12] Butanone fires should be extinguished with carbon dioxide, dry agents, or alcohol-resistant foam.[8]

Health effects

Butanone is a constituent of tobacco smoke.[17] It is an irritant, causing irritation to the eyes and nose of humans.[12] Serious animal health effects have been seen only at very high levels. There are no long-term studies with animals breathing or drinking it,[18] and no studies for carcinogenicity in animals breathing or drinking it.[19]:96 There is some evidence that butanone can potentiate the toxicity of other solvents, in contrast to the calculation of mixed solvent exposures by simply adding exposures.[20]

(As of 2010), the United States Environmental Protection Agency (EPA) listed butanone as a toxic chemical. There are reports of neuropsychological effects. It is rapidly absorbed through undamaged skin and lungs. It contributes to the formation of ground-level ozone, which is toxic in low concentrations.[16]

Regulation

Butanone is listed as a Table II precursor under the United Nations Convention Against Illicit Traffic in Narcotic Drugs and Psychotropic Substances.[21]

Emission of butanone was regulated in the US as a hazardous air pollutant, because it is a volatile organic compound contributing to the formation of tropospheric (ground-level) ozone. In 2005, the US Environmental Protection Agency removed butanone from the list of hazardous air pollutants (HAPs).[22][23][24]

See also

Notes

  1. ↑ The international standards group IUPAC has deprecated the term methyl ethyl ketone, and now recommends using ethyl methyl ketone instead.[2]

References

  1. ↑ Merck Index, 11th Edition, 5991.
  2. ↑ 2.0 2.1 2.2 2.3 Nomenclature of Organic Chemistry : IUPAC Recommendations and Preferred Names 2013 (Blue Book). Cambridge: The Royal Society of Chemistry. 2014. p. 725. doi:10.1039/9781849733069-FP001. ISBN 978-0-85404-182-4. 
  3. ↑ 3.0 3.1 3.2 3.3 3.4 3.5 NIOSH Pocket Guide to Chemical Hazards. "#0069". National Institute for Occupational Safety and Health (NIOSH). https://www.cdc.gov/niosh/npg/npgd0069.html. 
  4. ↑ "butan-2-one_msds". https://www.chemsrc.com/en/cas/78-93-3_1101392.html. 
  5. ↑ 5.0 5.1 5.2 5.3 "Safety Data Sheet - Klean Strip - Methyl Ethyl Ketone (MEK)" (in en). Klean Strip. 15 April 2015. http://www.kleanstrip.com/uploads/documents/GME71_SDS-1635.4.pdf. 
  6. ↑ 6.0 6.1 "2-Butanone". Immediately Dangerous to Life and Health Concentrations (IDLH). National Institute for Occupational Safety and Health (NIOSH). https://www.cdc.gov/niosh/idlh/78933.html. 
  7. ↑ 7.0 7.1 Wilhelm Neier, Guenter Strehlke "2-Butanone" in Ullmann's Encyclopedia of Industrial Chemistry, Wiley-VCH, Weinheim, 2002.
  8. ↑ 8.0 8.1 8.2 8.3 8.4 Turner, Charles F.; McCreery, Joseph W. (1981). The Chemistry of Fire and Hazardous Materials. Boston, Massachusetts: Allyn and Bacon, Inc.. pp. 118. ISBN 0-205-06912-6. 
  9. ↑ "Direct Routes to Phenol". http://www.chemistry.org/portal/a/c/s/1/feature_pro.html?id=c373e908e6e847ac8f6a17245d830100. 
  10. ↑ Ashford's Dictionary of Industrial Chemicals, Third edition, 2011, ISBN:978-0-9522674-3-0, pages 6013-4
  11. ↑ Apps, E. A. (1958). Printing Ink Technology. London: Leonard Hill [Books] Limited. pp. 101. https://archive.org/details/printinginktechn00apps. 
  12. ↑ 12.0 12.1 12.2 Fairhall, Lawrence T. (1957). Industrial Toxicology. Baltimore: The Williams and Wilkins Company. pp. 172–173. 
  13. ↑ Lange's Handbook of Chemistry, 10th ed. pp1496-1505
  14. ↑ CRC Handbook of Chemistry and Physics, 44th ed. pp 2143-2184
  15. ↑ Semon, W. L.; Damerell, V. R. (1943). "Dimethylglyoxime". Organic Syntheses. http://www.orgsyn.org/demo.aspx?prep=cv2p0204. ; Collective Volume, 2, pp. 204 
  16. ↑ 16.0 16.1 Simon B.N. Thompson (Winter 2010). "Implications for cognitive rehabilitation and brain injury from exposure to Methyl Ethyl Ketone (MEK): a review". Journal of Cognitive Rehabilitation 28(Winter): 4–14. http://www.jofcr.com/jcrarchives/vol28/v28i4thompson.pdf. 
  17. ↑ Talhout, Reinskje; Schulz, Thomas; Florek, Ewa; Van Benthem, Jan; Wester, Piet; Opperhuizen, Antoon (2011). "Hazardous Compounds in Tobacco Smoke". International Journal of Environmental Research and Public Health 8 (12): 613–628. doi:10.3390/ijerph8020613. ISSN 1660-4601. PMID 21556207. 
  18. ↑ "Methyl ethyl ketone (MEK) (CASRN 78-93-3)". EPA. 26 September 2003. http://www.epa.gov/iris/subst/0071.htm. 
  19. ↑ "US Toxicological review of Methyl ethyl ketone In Support of Summary Information on the Integrated Risk Information System (IRIS)". US Environmental Protection Agency. September 2003. pp. 152. http://www.epa.gov/iris/toxreviews/0071tr.pdf. 
  20. ↑ F D Dick. Solvent neurotoxicity, Occup Environ Med. 2006 Mar; 63(3): 221–226. doi:10.1136/oem.2005.022400, PMC 2078137
  21. ↑ List of Precursors and Chemicals Frequently Used in the Illicit Manufacture of Narcotic Drugs and Psychotropic Substances Under International Control , International Narcotics Control Board
  22. ↑ Federal Register Volume 70, Issue 242 (December 19, 2005)
  23. ↑ "MEK No Longer a HAP". Bfksolutions newsletter. n.d.. http://www.bfksolutions.com/index.php/newsletter/archived-newsletters/133-mek-no-longer-a-hap.  After technical review and consideration of public comments, EPA concluded that potential exposures to butanone emitted from industrial processes may not reasonably be anticipated to cause human health or environmental problems.[citation needed]
  24. ↑ "EPA De-Lists MEK from CAA HAP List". http://www.pcimag.com/articles/85504-epa-de-lists-mek-from-caa-hap-list. 

External links



Retrieved from "https://handwiki.org/wiki/index.php?title=Chemistry:Butanone&oldid=3324239"